A Thorough Chassis Evaluation Must Precede A Proper Alignment

A Thorough Chassis Evaluation Must Precede A Proper Alignment

Thanks to all the potholes caused by our harsh winter weather, we tend to do a lot of alignments here in Northeast Ohio. But wherever you live, it's a good idea to check the alignment whenever you put on a new set of tires or replace a worn suspension component. And, sometimes you might encounter a problem due to a unique chassis setup. Take the Volvo 850, S70 and V70, for example, which from 1993 to 2000 had a slightly different split rear axle setup that was adjustable.

photo 1Thanks to all the potholes caused by our harsh winter weather, we tend to do a lot of alignments here in Northeast Ohio. But wherever you live, it’s a good idea to check the alignment whenever you put on a new set of tires or replace a worn suspension component. And, sometimes you might encounter a problem due to a unique chassis setup.

Take the Volvo 850, S70 and V70, for example, which from 1993 to 2000 had a slightly different split rear axle setup that was adjustable. There are adjusting blocks bolted to the ends of the axle halves that slide into and are secured to the other side of the rear axle (see Illustration 1).illustration 1: 1  support arm, left, p/n 8600259 2  link, p/n  3516122 3  press screw, p/n  987341 4  flange lock nut, p/n 985870 4a  anchorage, p/n  9434000 5  bracket, left, p/n  9200189, 9492261 6  anchorage, left, p/n  3530202 7  hexagon screw, p/n  987186 8  sems screw, p/n  985358 9  flange nut , p/n  3546077 10  sems screw, p/n  977509 11  flange screw, p/n  985055 11a  washer, p/n  986445 12  hex, socket screw, p/n  987377 13  hub 14  grease cup, p/n  3516594 15  wheel axle, p/n  9157713 16  flange lock nut, p/n 9200250 17  support sleeve, p/n  9191388 18  switch actuator, p/n 9191387

When trying to do an alignment on these models, a common problem is frozen or broken rear axle alignment blocks (see Photo 1). If they are broken or frozen, the blocks will need to be ­replaced before an alignment can be done. If you’ve never done this job before, it can be a little tricky.

When a 1998 S70 came into our shop with some rear suspension noise, a quick check revealed that the right-side alignment block was broken (see Photo 2). This real-world scenario serves as photo 2a perfect opportunity to share some insight on making the job a little easier. We normally begin by doing the blocks on both sides, which enables us to then do a full 4-wheel alignment. Keep in mind that if you are buying an OE block from Volvo, you will need to buy all the hardware separately (see Photo 3). We use a kit that comes with all new hardware. Let’s get started.

1. Put the car on the lift and remove the rear wheels.photo 3

2. Remove the rear sway bar, which is held in only by two bolts on each side. In this part of the country it’s usually necessary to heat the nuts and bolts to get them loose (see ­Photos 4, 5  and 6). We like to use an inductive heater instead of torches, ­especially around the fuel tank. photo 4

3. Once the bolts are removed, it’s necessary to slide the sway bar all the way toward the driver’s side in order to get it out (see Photos 7 and 8). The driver’s-side axle block is the easy photo 5side. After removing the two adjusting bolts, the axle can be pulled back and the end bolt removed without much trouble. If the right-side axle block is broken, you may be able to pull photo 6the pieces out and then remove the end bolt. If it’s not broken, the end bolt can be accessed through the opening at the outside of the axle. 

4. Once the two blocks are removed, you can put the new blocks in. Always put the right side photo 7in first to make the job easier. Pull the end of the axle out and toward the rear of the car and put the new block in place.  

5. You will then need to start the end bolt through the access hole, which can be a little tricky (see Photo 9). You can torque the end bolt, but don’t put the two adjusting bolts in until the photo 8left-side block is in place. The left side is relatively easy. With the end of the axle pulled out toward the back of the car, the block can be bolted to the end of the axle and then slid back into place (see Photo 10).photo 9

6. Once both blocks are in place, install and snug the adjustment bolts (see Photo 11). They will get torqued during the alignment process.  photo 10

7. Reinstall the sway bar, torque the wheels and the car will now be ready for an alignment.

It’s important to remember that a proper alignment can’t be done if there are frozen or worn steering or suspension components. Be sure to inform any customer or potential customer that before any alignment can be done, you will first give the vehicle a thorough evaluation, and then subsequently inform them what repairs are necessary before the alignment can be started. That way, the unsuspecting customer won’t be surprised when you call to tell them about a worn tie rod, bad ball joint or broken axle block. You will be servicing the customer well and increasing Photo 11your bottom line by finding that extra, but necessary, work. 

You May Also Like

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Technology is defined as the application of scientific knowledge for practical purposes, especially in industry. We often picture technology as something that has computers and electronics attached, and often it does. But, in the world of impacts, both in the realm of pneumatic and cordless, technology bears much deeper roots.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter
More Than A Scan Tool

Scan tools serve as indispensable diagnostic hubs, offering access to a wealth of resources, from OEM technical bulletins to community-documented repairs.

scan tool
Battling Stress and Burnout

Here are some quick tips for managing stress and avoiding burnout in the fast-paced automotive repair industry.

Nadine Battah