Lisle Corporation

Lisle Corporation president, Frederick Vernon Lisle, passed away March 27, 2018.

The Combination Disc Brake Kit (29350) from Lisle Corp. is designed to work on single piston disc brakes that require the piston to be rotated back into the caliper as well as pistons that are pushed.

Drive tool between the gasket and then use a hammer from the side to separate the pan from the gasket.

The newest spark tester includes a coil-on-plug wire.

The newest brushes called TIME SAVER #1, #2 and #3 were made for large surface cleaning jobs.

The set's hardened steel plates are wire and spot welded for strength.

Both have innovative bullet-shaped tips that resist mushrooming.

Complete with a square notch design that removes plastic and metal clips, this Lisle tool helps eliminate broken fasteners.

The low profile design with 45° bend disconnects fuel line, EVAP line fittings and DEF fittings in hard-to-reach areas.

Air pressure is added to the water flow, creating agitation that flushes out even the most stubborn clogs.

Use the tool to accurately line up and hold cams for proper timing chain alignment on Honda K-Series engines.

This hanger from Lisle can be attached to most toolboxes, benches or walls to store plastic or metal creepers.

Adapt-a-Cap eliminates the need for external pumps, hoses or funnels to transfer fluids, and helps prevent spills and messes.

Disconnect fuel line, EVAP line and DEF fittings with tabs that must be depressed to disengage with these pliers.

Handy tools help techs remove radiator hoses from fittings and clamps.

The disconnects also work on fuel line quick connect couplings for GM, Ford and Chrysler vehicles. They are also easy to use in confined spaces.

The cross-cut tip design grips most hose clamps from multiple angles. A ratcheting lock mechanism holds the clamp in an open position for hands-free use.

Designed to prevent over-tightening lug nuts with a torque rating of 80 ft-lbs., Lisle Tools releases their 12200 three-piece Stubby Torque Stick set.

Designed for the GM EcoTec3 5.3L and 6.2L Motors.

Lisle's Low Profile Adjustable Seal Puller (55210) comes in two hook sizes that easily remove most oil and grease seals.

The new Lisle Battery Nut Pliers (55240) are used to loosen or tighten battery terminal clamp nuts.

Many applications are covered with this seven-piece set.

Milled slots guide the tool onto the lock rod retainer and keep it in place as the rod is removed.

Thin tips on the Lisle Double-Ended Tool provide easy access when removing plastic clips.

The new Lisle Actuator Motor Wrench Set is a toothless, infinite ratchet with a hinged handle design, which makes it easy to remove and replace fasteners on electric HVAC motors.

The socket features a partial hex design to fit 1-13/16 in. long oil pressure switches on 2015-2017 Ford and Lincoln vehicles with 4 and 6 cylinder engines.

The wrench has heat-treated arms with specially designed gripping jaws that grab even the most stubborn filters.

Lisle Corp.’s Manifold Drill Template (71400) removes broken exhaust manifold bolts on GM LS III 4.8L, 5.3L and 6.0L motors without damaging the cylinder head.

The lighted handle illuminates electrical connectors and the six quick-connect tools are designed to fit Deutsch HD10, HD20 and HD30 series connectors and Deutsch Jiffy Splices from AWG 4 to AWG 20.

These scrapers can be used to clean disc brake caliper slides. The tungsten carbide tips are brazed to the steel blade that is molded into the comfortable 6" long handle.

The strip tool has a range of 10-22 AWG stranded and 8-18 AWG solid wire.

A flexible 9" gooseneck design provides bends over 90° and rotates 360° to aim light where it is needed.

The tool helps ensure camshaft alignment during removal and installation of the timing chain.

On 6- and 8-cylinder engines, the wrench engages the ribs and flutes on the filter cap housing. Also works on 1.8L 4-cylinder engines.

The kit's cam adjusting holding tool surrounds the entire perimeter of each cam to provide a no-slip work area when moving OEM cams.

To be used with a vacuum pump, the kit includes large and small tapered stoppers, graduated catch can, two lids, tubing and three brake bleeder adapters.

This tool releases four sizes of spring lock couplings on A/C and fuel lines on many Chrysler and Ford vehicles.

Great for checking harness connectors and sensor wiring, these flexible silicone probes bend up to 180° for hard-to-reach areas.

The 5/8" opening of the pliers properly fits spark plug wire boots to help prevent damage.

The set includes tools for removing and installing brake springs along with parking brake and star wheel adjusting tools.

The 17282 quickly removes transmission oil from over-filled automatic transmissions. It also works great for adding oil to differentials.

The tools allow technicians to easily remove plastic push pin-type panel fasteners with center pins in tight spaces such as wheel wells.

This specially designed driver works with the included sockets or bit holder and 5/16" hex impact bits.

Clip the lead to the end of the wire in question and probe the other end of the wire. If the bulb lights up, continuity exists. If the bulb fails to light, the circuit is open.

Lisle’s Low Profile Plastic Creepers feature a comfortable, body-fitting design and are now available in pink, neon orange and neon green.

With an operating range of 3-49 volts DC to work on most vehicle electrical systems, the tool has 360° visibility of polarity.

This set includes a driving screw, thrust bearing and the 12 threaded adapters necessary to work on a wide range of domestic and some import harmonic balancers.

Use these tools with a 1/2" ratchet or other square drive for flexibility in tight spaces for removing and installing pressed and bolt-on water pump pulleys.

This 10-piece Stripped Screw Extractor Set, 61980, from Lisle Corp. features 10 sizes of extractors that fit Torx and Torx Plus sizes T-10 to T-55; internal hex sizes 7/64" to 3/8" and 3mm to 10mm.

The 1.6-qt. translucent funnel comes with seven different color-coded adapters and a 45° elbow to work on many applications and save valuable storage space.

This tool crimps insulated and non-insulated terminals from 10 to 22 gauge and 7mm to 8mm ignition terminals with a size key marked on the tool.

The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain.

This heavy-duty impact socket is designed with more than three times the standard socket mass to direct more energy to removing the bolt. It can be used on Honda engines that use a 19mm hex pulley damper bolt or other 19mm applications.

The kit’s interchangeable probes offer a wide range of testing possibilities. Test probes with 2mm pointed tip plug into banana test leads to eliminate the need to change leads.

The tools in Lisle Corporation’s Stepped Pickle Fork Kit (41440) feature a stepped design on the forks, which keeps the tool from bouncing back when separating ball joints, steering dampeners, tie rods, pitman arms and other applications.

Lisle’s Master Plus Disconnect Set (39850) is a compilation of the most popular disconnect tools for fuel line quick connect and spring lock couplings, air conditioning line couplings and transmission oil cooler connectors in one handy molded case.

This Multi-Position Magnetic Cup features a strong magnetic base that attaches securely to vehicles, tool boxes, bins, hoists and any other ­ferrous metal object. The angled design allows it to be positioned at any angle. The strong magnet can hold up to 5 lbs. in a vertical position.

This spark plug remover kit includes tools to remove broken spark plugs from 2004 to 2008 Ford Triton three-valve per cylinder engines. The kit includes a Porcelain Puller Tool, Porcelain Pusher and a Self-Tapping Puller -- all in a blow-molded plastic case for storage.

Use Lisle’s Small Fastener Remover (60530) with a pneumatic impact tool to loosen rusted or seized fasteners. A 3/4″ open end wrench can be used to turn the socket while impacting the fastener. A locking pin in the driver keeps the bit holder in place on the square drive for safe operation. The bit holder

Great for working on wheels or brakes, the Lisle 93502 Low Profile Seat Creeper is also useful for body work. The adjustable, cushioned backrest can be removed for use as a knee creeper when working under the dash.

The Lisle 46200 Snap Ring Pliers quickly convert from internal to external use. Simply pivot each handle to the opposite side to reverse action. The smaller design is made to fit tight spaces.

Three pairs of metric threaded wheel stud pilot pins allow you to hang the wheel without having to balance it on the small lip of the hub.

Plug a scanner into Lisle Corp.’s OBD II Splitter with Power & Ground to activate certain circuits while having access to power and ground for use with a multimeter, scope or test light.