Diagnostic Solutions: Diagnosing Misfires

Diagnostic Solutions: Diagnosing Misfires

Although diagnosing misfires can be a tough assignment for any driveability technician, the diagnosis can be made much simpler if he understands the basics of misfire diagnosis. For example, when the first OBD II misfire monitor was first introduced in 1996, technicians were puzzled by problems with false misfire diagnostic trouble codes (DTCs). Case in point, vehicles being driven on washboard dirt roads began recording false misfires.

air/fuel ratios caused by leaking fuel pressure regulators and other fuel control issues can also cause general misfires on other vehicles. Freeze-frame data obtained by a scan tool can be used to determine the conditions under which a general misfire has occurred.

In these cases, short- and long-term fuel trim numbers can be used to help diagnose a general misfire condition. If the PCM is adding fuel at idle, or if the fuel trim is adding fuel to one cylinder bank, suspect a vacuum leak. If the fuel trim is subtracting fuel, suspect a leaking fuel pressure regulator, fuel-contaminated crankcase oil, or other component failure that introduces excess fuel into the cylinders.

If, during a road-speed test, the fuel trim numbers exceed 10% positive, the PCM is compensating for a failure or set of failures that are causing a lean fuel condition. Here again, any condition or failure that causes a loss of fuel pressure or incorrect metering of engine intake air can also cause a general misfire condition. Keep in mind that a contaminated hot-wire MAF sensor often causes an engine to run rich at idle and lean at high speeds.

UNUSUAL MISFIRE PROBLEMS

When diagnosing a misfire problem, remember that the PCM is actually looking for a momentary deceleration in the rotating crankshaft assembly. To illustrate, I’ve had a sunflower seed shell caught in a MAF sensor cause a general misfire. If the shell turned edgewise, the engine ran great. If the vehicle hit a bump, the shell would turn sidewise and block the airflow through the MAF sensor and cause the air/fuel mixture to go lean, which created multiple misfire codes.

In another case, I had a brand-new CKP sensor indicate misfires at road speed as fast as the PCM could count them. Last, worn valve seats and guides can create an intermittent misfire condition by causing an intermittent loss of compression.

Other unusual issues that have been reported to me are heavy lap splices in serpentine belts and vapor bubbles forming in single-line fuel systems that eventually cause random fuel injector misfires. Last, but not least, are the efforts of some amateur techs causing a misfire by replacing the dual-electrode plug used on some Toyota engines with single-electrode spark plugs.

In other cases, substituting a plated, long-life spark plug with a non-plated, steel-shell spark plug will cause a misfire due to the less efficient electrode configuration and considerably shorter service life of the cheaper spark plug.

To prevent the MIL from illuminating due to a P0300-series misfire, it’s always best to replace ignition parts at specified intervals with OE or OE-equivalent parts. Always allow an engine to cool before removing the spark plugs. When replacing a seized spark plug, soak the threads with high-quality penetrant and alternately tighten and loosen the spark plug in about 1/8-turn increments until it turns free. Thoroughly clean the spark plug seating area.

Last, tighten the new spark plugs to the manufacturer’s recommendation and apply a small amount of dielectric grease to the inside of the coil or wire boot before installation.

some misfire-related dtcs describe primary ignition and fuel injector failures.cardboard or plastic sleeves protect the electrodes and electrode air gaps on most long-life spark plugs.grasping a spark plug by its threads will prevent contaminating the insulator with greasy fingerprints.use a clean spark plug boot or dedicated holding tool to handle and install new spark plugs.improper handling can easily damage electrodes plated with precious metals. always use the correct tools to adjust spark plug gap.if the air gap must be increased, use a recommended tool to gently lift the ground electrode.if the air gap must be reduced, gently tap the ground electrode with the gapping tool.if recommended by the auto manufacturer, brush a very small amount of the recommended anti-seize compound on the threads directly behind the ground electrode.always inspect the spark plug boot for carbon tracking, oil saturation or perforation.Cleanliness is always important on modern engines. Before removing spark plug, use compressed air to blow debris out of spark plug well. Clean the seating surface before installing the new spark plug. Don’t forget your safety glasses!

You May Also Like

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Technology is defined as the application of scientific knowledge for practical purposes, especially in industry. We often picture technology as something that has computers and electronics attached, and often it does. But, in the world of impacts, both in the realm of pneumatic and cordless, technology bears much deeper roots.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

Software Focus: Efficient Diagnostics

Discover how to quickly retrieve codes, access exclusive repair information, and develop a strategic plan for optimal diagnostic results. This video is sponsored by Bosch.

Why ECU Reflashing Needs Certain Power Levels

A reflash power supply is not designed to jumpstart the vehicle.

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.