Eye Protection and PPE

On the Job: Eye Protection

Most employees want to work in a safe manner. So why do these preventable eye injuries keep occurring?

Employers must commit time, energy and resources to purchasing and providing PPE to their employees. Yet, an estimated 2,000 work-related eye injuries occur every day in the United States, with studies showing 90% of those injuries are preventable. More than 75% of those injuries are from employees choosing to not wear the eye protection provided for the task. 

Most employees want to work in a safe manner. So why do these preventable eye injuries keep occurring? How do we reduce the frequency and severity of these injuries? 

Click HERE to read “The Eyes Have It: Protecting Employee Vision with PPE” from OH&S.

You May Also Like

Scan Tool Tech

While systems can and will differ, here’s a look at common ADAS features, their general configurations and calibration requirements.

scan tool tech

Advanced Driver Assistance Systems (ADAS) require the use of a scan tool for diagnostics, and the majority of the time, it’s required for post-repair calibration. ADAS, like any other system, requires a diagnostic routine, which begins with a base knowledge of the system. Knowing ADAS will help understand fault symptoms and scan tool data for the most efficient diagnosis.While systems can and will differ, here’s a look at common ADAS features, their general configurations and calibration requirements.Parking assist sensors, of which there can be more than one, are generally located in the front and rear bumpers. They are the inputs that affect active parking assist and parking collision warnings. Any time they are disturbed in any manner, a static calibration must be performed with a scan tool.Side object sensors, sometimes called collision avoidance sensors, are commonly located in the rear bumper. These sensors provide input for blind spot warnings, lane change alerts and rear cross traffic warnings. Static calibration with a scan tool is required when these are removed or replaced.Rear vision cameras will be located in the rear decklid, liftgate or tailgate, and act as either a backup camera alone, or part of a surround view system if the vehicle is so equipped. These cameras generally require a dynamic calibration, and no scan tool is required.A forward-looking camera is sometimes located behind the grille, and usually part of a surround view system. These too do not require a scan tool, but a dynamic calibration must be performed when they are removed or replaced.Different ADAS features may have dedicated control modules which can be located in various areas, often behind interior panels. As with most control modules, these require scan tool programming when replaced and, depending on the system, both static and dynamic calibrations may be required.The Haptic Seat Motor creates the vibration to provide a safety alert for blind spot, forward collision, lane departure, lane keep assist, parking collision and rear cross traffic warnings. These motors, sometimes called seat warning actuators, generally require no type of calibration.Cameras located in a sideview mirror are part of surround view systems. These require calibration when removed or replaced, but most of them dynamic, and no scan tool is required.The steering angle sensor located in the steering column is an input for lane keep assistance, and a static calibration is required with a scan tool any time it is removed or replaced, or any time a wheel alignment is performed.Last, but not least, is the front view, or forward-looking camera located in the windshield area. This camera is a vital part of adaptive cruise control, automatic emergency braking, automatic high beam headlights, forward collision and lane departure warnings, and lane keeping assistance. A scan tool and static and dynamic calibration are required after removal and replacement, but also after windshield removal or replacement, or any service that affects the ride height of the vehicle. TS

Smash the Peppermint Pig

What’s the best tool an auto technician can own? Is it really possible to say?

Drywall Pro’s Invention Becomes a Hit with Auto Painters

We love how inventive people are! Here’s a great story of someone who developed a tool auto repair techs can use too!

Drywall Pro’s Invention Becomes a Hit with Auto Painters
The Latest in Auto Repair Workwear

Here’s a look into the many options available in today’s workwear specifically designed for automotive technicians.

Auto Shop Clean Up

It may take a little more planning, but keeping a clean shop is a good move for the industry and good for your business.

Clean auto shop

Other Posts

Clutch “No Release” Problems

Poor clutch release makes it difficult to start and stop the vehicle or change gears.

Fine-Tuning Your Wheel Balancing Process

The first step to a smooth ride and well-balanced tire has nothing to do with the balancer.

Upgrade Your Air System: It’s Easier Than You Think

Improving your shop airflow is only a benefit, unless you like to spend more time, work harder and make less money.

air flow tubes
Why ECU Reflashing Needs Certain Power Levels

A reflash power supply is not designed to jumpstart the vehicle.