How Often Is Lift Maintenance Needed?

How Often Is Lift Maintenance Needed?

If something doesn’t seem right, stop using the lift until you can get it checked out. Never use a lift if any component is broken or damaged.

Even the most rugged, low-maintenance lifts need attention from time-to-time.

Give your lift a once over every day before you use it, checking the safety devices, operating controls, lift arms and all moving parts to make sure everything is functioning properly. Look for breakage, excessive wear or other conditions that may affect its performance. Be sure to check your adapters — it’s critical to your safety that they’re not damaged, missing their rubber pads or excessively worn.

Keep an eye and an ear out for any unusual sounds or issues when using your lift. If something doesn’t seem right, stop using the lift until you can get it checked out. Never use a lift if any component is broken or damaged or if you see signs of an oil leak. Call a lift service professional.

Your owner’s manual should lay out the specific maintenance requirements for your lift, but for an overview, here’s the minimum you should do monthly for most two-post and four-post lifts.

Monthly Checklist

  • Visually inspect all moving parts and all cables for signs of excessive wear.
  • Check all arm adjusting locks to make sure they’re operating properly.
  • Check all cable connections, bolts and pins to ensure proper mounting and torque.
  • Visually inspect safety locks for proper operation.
  • Lubricate posts with grease if required.
  • Lubricate locking latch shafts. Push the latch handle/release arm several times for oil to penetrate the pivot points.
  • Inspect all anchor bolts and tighten if necessary.
  • Check all posts to make sure they are square and plumb.
  • Inspect all pivot arm pins to ensure they are properly secure.
  • Check cable tension and adjust if necessary.
  • If the lift is equipped with an overhead micro-switch, make sure it is operating correctly.
  • Check the equalizer cable tension and adjust per the owner’s manual if needed.
  • Replace any missing or damaged caution, warning or safety-related decals. You can order new ones from your lift manufacturer.

If cement anchor bolts are loose or any lift component is found to be defective, do not use the lift. Call a qualified lift service professional to repair it. Never put a lift back into operation until all faulty parts have been replaced with genuine OEM replacement parts.

Finally, always keep your lift and its components clean.

BendPak, Inc.
BendPak logo
Phone: 805-933-9970Fax: 805-933-9160

You May Also Like

Mercedes EQS Service Opportunities

EQ is the EV brand for Mercedes. It is the equivalent of Audi’s Etron or VW’s iD brands.

Vs from German manufacturers Mercedes, Audi and VW. Many of these offerings were SUVs and crossovers. One of the rare sedans was the Mercedes-Benz EQS. Think of the ESQ as the S-Class of EVs. It has several unique features and a complete suite of ADAS and autonomous features.

View the TechShop Buyer’s Guide Today

With the instant power of the internet, a complete list of tool manufacturers and company information is at your fingertips.

Tool button on a keyboard
Key Programming Challenges And Opportunities

For most vehicles today, it’s not so much about programming a new key to the car, but programming the car to the key.

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Customer Relations

Customer relations are crucial; a single negative encounter can lead to consequences.

Technician speaking to customer

Other Posts

BendPak Full-Rise Scissor Lift Delivers Two-Post Performance

SP-7XE scissor lift lays flat and raises a vehicle six feet with an open center below.

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool
BendPak to Debut Eight-Armed Car Lift Concept at NADA

Octa-Flex improves technician productivity, convenience and ergonomics, according to BendPak.