Mac Tools Introduces the New Spot Weld Drill Kit

Mac Tools Introduces the New Spot Weld Drill Kit

The new Spot Weld Drill Kit, part number ASWD317, is part of the extensive Mac Tools Power Tools line and boasts many features making it an absolute necessity for paint and body shops. This exclusive kit includes two anvils and three drill sizes providing multiple solutions for all paint and body drilling jobs.

The new Spot Weld Drill Kit, part number ASWD317, is part of the extensive Mac Tools Power Tools line and boasts many features making it an absolute necessity for paint and body shops. This exclusive kit includes two anvils and three drill sizes providing multiple solutions for all paint and body drilling jobs. With its high torque and low speed this drill is perfect for maximum power and control!

With 1/4” air inlet, 1,600 RPM and four CFM average air consumption, the new Mac Tools Spot Weld Drill has the power to get the job done fast. The two-position trigger sets the anvil location and then starts the drill, assuring accurate location and diameter as the Vernier stop then sets the depth of cut. Premium titanium coated drill sizes: 6.5 mm, 8.0 mm and 10 mm are included. The specially designed hard case provides the Spot Weld Drill Kit convenient storage no matter which anvil is left on the drill. Quality, precision, convenience: the Mac Tools Spot Weld Drill Kit – The answer to every spot weld drilling job!

To order the Mac Tools Spot Weld Drill Kit, part number ASWD317, contact your local Mac Tools distributor or call 1-800-MACTOOLS.

For more information, visit www.mactools.com.

You May Also Like

Pulling Codes: Multiple Misfire Personalities

A vehicle fails an emission test due to a series of codes, with misfire activity found on cylinders 2, 4, 6, 8 and 3 – and a strange metallic sound can be heard when the rpms are raised. See how Carlton Banks solves this latest Pulling Codes case.

A Story of Codes P0302, 04, 06, 08 & 03
 

This month’s diagnostic journey begins with a 2008 Land Rover Discovery that is taken in to a local testing facility for an emission test and fails due to a series of misfire codes.

Misfire activity is found on cylinders 2, 4, 6, 8 and 3; at first glance this series of codes implies that there may be bank 2 issues, but the cylinder 3 code throws a wrench into that mode of thought.

Using Volumetric Efficiency to Determine the Health of an Engine

Using an OBD II scan tool/dynamometer simulation/calculation program that can graph volumetric efficiency (VE) over rpms, contributor Glen Beanard devised a test sequence using real-world vehicles. This article takes you step by step through his diagnostic process.

Intermittent Engine Misfire Analysis

Even for an experienced diagnostic technician, attempting to diagnose an intermittent misfire condition that occurs only under specific driving conditions can be a frustrating exercise. Contributor Gary Goms breaks it down, and includes tips for using a scan tool and a lab scope.

5 Mistakes Newbie Tire Techs Make

Nothing can turn a new tech into a veteran but time and experience, and often that experience is going to come from making mistakes – sometimes real bad ones – and learning from them (you hope). By addressing these most common mistakes right away with new tire techs, the worst of them can be avoided.

Rivet Bonding Comes Full Blast

Now that rivet bonding is in the mainstream with the Ford F-150, it’s time for shops to look into training and equipment for this repair process.

Other Posts

‘Test Before Touch’ – It’s No Waste of Time

To help reduce the headaches involved in servicing TPMS, it’s important to use the “Test Before Touch” procedures in your shop. Used properly, TBT can form a strong foundation for everything else you do regarding TPMS, reduce complexity and help you educate and keep your customers.

The Right Diagnostic Tools Save You From Extensive Disassembly Time

It can sometimes be difficult to make the correct diagnosis for a hard-to-start complaint. And diagnostic time may be extensive — and expensive. This article shows how certain tools have the ability to automatically analyze waveforms for you.

Know the Specs for Your Social Media Accounts

If you’re doing social media, are you doing it effectively? Are your accounts set up correctly? Are you posting often enough? Mark Claypool answers some questions.

Top 5 Tools: Kenny Younkins, Ken’s Auto Service Center

Kenny Younkins, owner Related Articles – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set – Mayhew Debuts New Fluorescent Handled Screwdrivers Ken’s Auto Service Center Akron, OH While Ken first said his favorite tool is his fishing rod, he said in the shop he prefers these five: