Nissan Tech Tip: Coolant Leak from Intake Manifold Water Outlet

Nissan Tech Tip: Coolant Leak from Intake Manifold Water Outlet

Some Nissan owners may find engine coolant under the vehicle when parked or smell coolant when the engine is warm. The cause may be coolant leaking between the water outlet housing and intake manifold sealing surfaces.

Applied Vehicles:
• All 2000-’02 Frontier (D22) with a VG33E engine; and
• All 2000-’02 Xterra (WD22) with a VG33E engine.

An applied vehicle may exhibit:
• Engine coolant under the vehicle when parked; or
• Smell of coolant when the engine is warm.

The cause may be coolant leaking between the water outlet housing and intake manifold sealing surfaces (See Figure). Refer to the Service Procedure to resolve this incident if it occurs.
Note: A leak from the above-noted area can be verified by a visual inspection.

Service Procedure:
Install the new fiber gasket between the water outlet housing and intake manifold as follows:
Caution: Be careful not to spill engine coolant on electrical connectors, drive belts, etc. when performing the following procedure.
1. Verify the coolant leak is coming from the water outlet housing/intake manifold sealing surfaces.
2. Use the valve on the lower radiator tank to drain coolant into a clean bucket (or other clean, suitable container), to just below the level of the water outlet housing.
Note: Draining the coolant below the level of the water outlet housing will minimize coolant spillage when removing the housing.
3. Remove the parts necessary to access the water outlet housing.
4. Remove the water outlet housing from the intake manifold.
5. Thoroughly clean the sealing surfaces of the water outlet housing and intake manifold, making sure all old sealer is completely removed.
6. Install the new fiber gasket onto the water outlet housing as follows:
a. First, install the two mounting bolts through the holes in the water outlet housing.
b. Then, slide the fiber gasket over the bolts until it is flush against the sealing surface of the housing. The bolts will keep the gasket in place while installing the housing.
7. Install the water outlet housing to the intake manifold and tighten the bolts to 16.3-20.3 Nm (12-15 ft.-lbs.).
8. Reinstall all components that were previously removed.
9. Refill the radiator with the coolant that was drained and captured in step 2, and according to the Coolant Refilling Procedure outlined in the “MA” section of the applicable service manual, to ensure air bubbles are purged from the cooling system.
Note: If additional coolant is needed, use a 50/50 mixture of Genuine Nissan Antifreeze Coolant (or equivalent) and distilled water or demineralized water.
10. Run the engine and confirm there is no coolant leak(s).

Technical service bulletin courtesy of ALLDATA.

For additional tech tips, visit www.alldata.com.

You May Also Like

Mullen Road Tests Solid-State Polymer Battery Pack

The results met or exceeded all requirements targeted for the first drive cycles for energy usage and driving range.

Mullen Automotive began Class 1 EV cargo van road testing with an integrated solid-state polymer battery pack. Vehicle road testing began on Feb. 26 at Mullen’s Commercial Tech Center in Troy, MI.

Mullen’s latest phase of solid-state polymer battery testing began in January with the installation of the battery pack into the Class 1 EV cargo van for testing system compatibility between the vehicle and pack. Recent performance testing has included on-road drive cycles as well as Dyno testing at an EPA-certified lab located in Northville, MI, Mullen said.

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

TurnOnGreen, Endliss Power Team up to Expand EV Charging

TurnOnGreen said it will leverage EPI’s expertise in administering and executing power purchase agreements with commercial clients.

Autel’s ADAS Bay Max Vehicle Lift

Learn how this lift integrates mechanical repair, four-wheel alignment, and ADAS calibration, prioritizing efficiency and space utilization in your shop.

Switch EV Trainer Provides Tailored EV Tech Training

The Switch EV Trainer includes all of the components of a modern EV drivetrain on a compact, insulated, mobile platform.

Other Posts

Tool Time Podcast: SATA USA

In this all new episode of the Tool Time Podcast, Nadine and Eric sit down with Chris Springer of SATA USA.

Elywhere Launches in North America

Elywhere chargers can be configured to support power in the 1 MW range, providing solutions for electric fleets.

#3 Screwdriver “Tips”

What appears as one of the most basic tools in your box is far from it.

#2 Calipers & Micrometers

Calipers and Micrometers are essential measuring tools when exact precision is required.