Nissan Tech Tip: ECM Replacement Service Procedure

Nissan Tech Tip: ECM Replacement Service Procedure

If you confirm that the Electronic Control Module (ECM) needs to be replaced on a 2000 MY or later Nissan vehicle, or a 1999 MY vehicle Frontier (D22), Quest (V41) or Pathfinder (R50) from VIN JN8AR07**XW350101, complete the following actions.

If you confirm that the Electronic Control Module (ECM) needs to be replaced on a 2000 MY or later Nissan vehicle, or a 1999 MY vehicle Frontier (D22), Quest (V41) or Pathfinder (R50) from VIN JN8AR07**XW350101, complete the following actions.

Caution: Failure to perform all of the work steps in the specified order can cause poor engine running, MIL on or vehicle emission test rejection.

SERVICE PROCEDURE:
Check NATS on the Vehicle
1. Check if the vehicle you’re working on has “ECM based” NATS V2.0 or V5.0.a. If so, it will not start after you install a service replacement ECM. So you’ll have to re-register all ignition keys, including spare keys with CONSULT-II and the purple NATS card. After you do this, proceed with step 2.
• If you do not know how to re-register the keys, refer to the ESM for the NATS key re-registration procedure.
b. If the vehicle has “BCM based” NATS, you do not have to re-register the ignition or spare keys. Proceed with step 2.

Check for ECM Data Updates in ASIST
2. In ASIST, select CONSULT Utilities >> ECM/TCM Data. Then choose Model and Model Year.

3. Look for ECM Data Updates (listed by ECM P/Ns and vehicle configuration) in the top, center display panel of the ASIST screen.
a. If there are no updates listed for your vehicle configuration, you do not have to reprogram the service replacement ECM. Proceed with step 5.
b. If there are updates listed for your vehicle configuration, see if they apply to the service replacement ECM you’re going to install. Do this by performing step 4.

4. Select the configuration on the screen for the vehicle you’re working on. Then confirm that your ECM is listed in the “Replaces 2371 0-XXXXX, -XXXXX, etc” section in the lower, center “Details” panel of the ASIST screen.
a. If your ECM is listed in the “Details” panel, you must reprogram the ECM with the latest data update. After you do this, proceed with step 5.
Caution: The 1999-2000 Frontier and 1999-2000 Pathfinder have a gray CONSULT connector and a white GST connector. Do not attempt to perform the ECM Reprogramming procedure with CONSULT-II connected to the gray CONSULT connector. See the appropriate engine service manual for further details if necessary.
b. If your ECM is not listed in the “Details” panel, you do not have to reprogram the ECM. Proceed with step 5.

Accelerator Pedal and Throttle Valve
Closed Position Learning
5. Perform as follows:
a. Make sure the accelerator pedal is fully released.
b. Turn the ignition switch “On” for 2 seconds.
c. Turn the ignition switch “Off” for 10 seconds.
d. Turn the ignition switch “On” for 2 seconds, then
e. Turn the ignition switch “Off” again for 10 seconds.
f. Proceed with step 6.

Perform Idle Air Volume Learning (IAVL)
Note: Make sure all electrical loads are turned off, including A/C, defroster, radio, lights, etc. while performing the following procedures. Also, make sure the engine cooling fans are not operating during the following procedures.
6. Perform as follows:
a. Connect CONSULT-II to the vehicle.
b. Warm up the engine and transmission to operating temperature.
c. In the CONSULT WORK SUPPORT mode, select IDLE AIR VOL LEARN.
• If IDLE AIR VOL LEARN is not shown as a SELECT WORK ITEM on CONSULT, the vehicle does not need the procedure.
• In this case only, this bulletin is complete, no further action is needed.
d. Press START on the “IDLE AIR VOL LEARN” screen.
e. Press START on the “WORK SUPPORT” screen to begin the Idle Air Volume Learning (IAVL) procedure.
• The IAVL procedure will take several minutes to complete.
• CONSULT will display “Please Wait” in the center of the screen while the IAVL procedure is in process.
• CONSULT will display “CMPLT” in the top right corner of the screen when the IAVL procedure is finished.
f. Once the IAVL procedure is finished, proceed with step 7.

For 2005 and Later MY Vehicles Only:
7. Enter the VIN into the new service replacement ECM as follows:
a. Select ENGINE on the “Select System” screen.
b. Select WORK SUPPORT on the “Select Diag Mode” screen.
c. Scroll down and select VIN REGISTRATION on the “Select Work Item” screen.
d. Press START on the “VIN Registration” screen.
e. Select INPUT on the “VIN Registration” screen.
f. Enter the entire VIN using the keyboard.
• Use CHNG to switch between the letters and numbers keyboard screens.
g. Once the entire VIN is entered, select ENTER on the keyboard screen.
h. Select INPUT on the “VIN Registration” screen and enter the entire VIN again. Then hit ENTER.
• You must enter the VIN a second time for confirmation purposes.
i. Select START on the “VIN Registration” screen to complete the VIN registration process.
j. Turn off the ignition switch and wait at least 10 seconds.

Courtesy of Identifix.

For additional information, visit www.identifix.com.

You May Also Like

Myers Tire Supply Introduces MTS Xpresstm

The innovative solution to consolidate purchases and control inventory costs.

Myers Tire Supply has announced the launch of MTS Xpress, a proprietary platform to help customers gain control while consolidating their purchases and streamlining their inventories. 

MTS Xpress from Myers Tire Supply is designed to help customers regain control of their inventory and lower their operating costs.  It is a proprietary inventory management solution connecting the customers’ needs to Myers’ inventory with the help of a downloadable mobile app.  With MTS Xpress, a Myers Tire Supply representative or any authorized customer employee can order an unlimited number of consumables, making sure the right products are on their shelves at the right time.  MTS Xpress will help our customers consolidate their suppliers, reduce purchasing costs by streamlining the entire acquisition process and gain control of their inventory.

Experiencing What the Tool Industry Has to Offer

ETI held its annual ToolTech conference April 17-19 at the Hyatt Regency Tamaya Resort in Santa Ana Pueblo, New Mexico.

Sandia Mountains
LIQUI MOLY Develops Liquid Thermal Manager for EV Batteries

The automotive chemical specialist is expanding its range for all-electric vehicles with Battery Coolant EV 200.

May 2023 Vehicle Care RockStar: Johnny Weber

Johnny Weber exudes confidence in his abilities to lead the band through proficiency over pageantry.

Variable Valve Timing Systems

Variable valve timing systems allow today’s engines to maximize performance and drivability.

Other Posts

Continental Tire Upgrades Test Tracks for EVs

Continental expanded its EV charging infrastructure at three company-owned test sites in Sweden, Germany and the U.S.

Streamlight Names E.A. Langenfeld & Associates 2022 Automotive Sales Rep Agency of the Year

The company received the award yet again in recognition for outstanding national sales achievement.

MAHLE and Midtronics Join Forces for Battery Service 

The goal of the cooperation: holistic battery diagnostics and maintenance from a single source in a growing future market.

Mitchell Announces Data Licensing Agreement with Rivian

Agreement reaffirms Mitchell’s commitment to proper and safe repair as electric vehicle adoption surges.