Reprogramming ABS Controllers

Reprogramming ABS Controllers

Reflashing undercar controllers is possible at your shop!

There are approximately 12 million “out of warranty” GM vehicles on the road today that can be flash programmed for update. From model year 2001 to 2005 there are more than 500 reprogrammable controllers, including brakes and traction control, of which two or more can be on an individual vehicle. As a business professional, there is a question that should be answered before investing in the hardware and subscriptions to perform reprogramming. Do you have a customer base that will support the cost of the hardware, subscriptions and training for reprogramming and provide a profit? If the answer is “No,” you will need to select a vendor that can supply a preprogrammed controller.

Since 1981, there has been a new station at the end of the assembly line. The Assembly Line Data Link (ALDL) connects the vehicle to a computer. This connection verifies that the Computer Command Control system and components are operating properly.

There could be one base Engine Control Module (ECM) for several engine types, each with the programming for a specific engine contained in a separate replaceable integrated circuit or “chip” called a Programmable Read Only Memory (PROM).

In the late 1980s, the manufacturers started equipping cars with anti-lock brakes. Many of these systems had a separate computer and ALDL and PROM.  

Reprogramming these vehicles required replacing the PROM. In some cases, the entire ABS control unit needed to be replaced. This was a very costly fix for a software problem.

End-of-line repair technicians had access to hand-held devices that could read DTCs plus input and output information. The manufacturers of the end-of-line equipment saw the possibility of the hand-held device for use in dealerships. Tool and equipment manufacturers also saw the possibilities and began to produce scan tools for the OEs and the aftermarket.

In 1996, OBD II introduced flash programming through the use of the scan tool, eliminating the replacement of the PROM. The ALDL and other diagnostic connectors were replaced with an SAE standard J1962 16-pin Diagnostic Link Connector (DLC). Some ABS and traction control systems have kept their own ALDL, but these are becoming the exception rather than the rule.

Flash Drivessome of these chips can be re-flashed.
Flash reprogramming is made possible by the Electronically Erasable Program Read Only Memory (EEPROM). The EEPROM is an integrated circuit component of the controller. Today it is referred to as a flash drive. Flash drives have been incorporated into most controllers since 1996 and provide the ability to download new programming through the DLC or a direct connection to the controller.

Flash Programming 101

Reprogramming electronic control modules requires knowledge and experience to successfully use the internet to download programming data and transfer it to a vehicle controller. To perform reprogramming, your shop should be equipped with a broadband internet connection that offers speeds of up to 1.5Mbps or greater. Dial up isn’t going to cut it.

To download a program you will need a laptop or desktop computer with a processor speed of 1GHz or greater with Windows XP. My recommendation is that this machine be dedicated to diagnostics and reprogramming. A dedicated hard drive would also be a good idea. After logging in to a manufacturer’s website, a technician will need to navigate to the proper screens to obtain the information for the vehicle and to download the new flash program.

The most convenient means of reprogramming is the use of the DLC interface. This can be accomplished with a scan tool or an SAE J2534 pass-through interface.

Go to the web page and enter the VIN number. Compare the current calibration in the vehicle to the latest calibrations posted. In the case of vehicles utilizing a Controlled Area Network (CAN) buss circuit, one or more of its controllers may require reprogramming. Connect the scan tool or J2534 interface and compare the calibration information and download the required reprogramming updates.As CAN bus systems have improved, more modules have their own controllers.

Before you begin the reprogramming make sure the battery is fully charged. You do NOT want any loss of voltage as this can cause real problems. You can use a battery charger that is voltage regulated with a range of 13.2 to 14.1 volts to ensure that the download is successful.

Follow the instructions for the download. The download may contain a documentation file. Be sure to read and follow all instructions before you start the transfer of data. As the software is loaded, there will be a display showing the progress of the download. This reprogramming procedure may take up to 30 minutes or more depending on the file size. Note: The GM setup will NOT allow the same calibration to be reinstalled. Only an updated calibration can be downloaded into the vehicle controller. There will be a message when the program has been successfully downloaded.

After a successful download, there may be relearn procedures such as a “CASE” relearn for a GM PCM to learn the relative positions between the crankshaft and camshaft sensors. If you don’t do the CASE relearn, the Check Engine Light will come on and there will be a code P1336.

The vehicle should be taken for a test drive to check vehicle operation. The new program will have none of the learned memory from the old program and could require an extended drive time to relearn all functions such as block learn fuel control.

Reprogramming has been a part of maintenance and repair for more than 10 years and you probably have all of the equipment to perform the service. It is an opportunity to extend full service to your customer.

You May Also Like

Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool

If there’s a truth that extends across all computerized devices, it’s that we likely utilize only a fraction of the things they have the ability to do. Mobile phones are a great example. How many people do you know who only use them for calls, voicemail and text messages? We all know they do so much more.The scan tools we use every day fall into the same category. Are you maximizing yours to their full potential? Don’t let them be just an expensive code reader. That may be easier said than done, because it takes a lot of time to understand both the scan tool and how well it interacts with the vehicles you’re working on, but there are a few factors that can help you dive a little deeper into the functions at your fingertips.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Matco Debuts 5-Piece Purple Screwdriver Set – Mayhew Debuts New Fluorescent Handled Screwdrivers – Snap-on Lights Up the New Year with New Lighting Tools   OTC Genisys Touch – Quick scan, bidirectional control Snap-on VANTAGE

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

2024 Is Your Year to Be the Technician You Always Wanted to Be

As we enter 2024, strategic career planning is essential for success in the automotive repair industry.

happy new year 2024
Software Focus: Efficient Diagnostics

Discover how to quickly retrieve codes, access exclusive repair information, and develop a strategic plan for optimal diagnostic results. This video is sponsored by Bosch.

PRT Heavy Duty Presenting Innovations at HDAW ‘24

PRT is exhibiting a full line of shocks and air springs for heavy-duty applications.

Why ECU Reflashing Needs Certain Power Levels

A reflash power supply is not designed to jumpstart the vehicle.