Rex-Cut Offers Flexible Grinding Discs for Contoured Surfaces

Rex-Cut Offers Flexible Grinding Discs for Contoured Surfaces

A line of flexible cotton fiber impregnated abrasive grinding discs that are ideal for the light grinding and blending of welds on contoured surfaces is available from Rex-Cut Products, Inc. of Fall River, MA.

A line of flexible cotton fiber impregnated abrasive grinding discs that are ideal for the light grinding and blending of welds on contoured surfaces is available from Rex-Cut Products, Inc. of Fall River, MA.

Rex-Cut Cut-N-Finish Discs are constructed of multiple layers of cotton fiber that are fully impregnated with aluminum oxide abrasives and pressed and bonded together to constantly expose fresh abrasives as they work. Pressed into a waffle pattern that runs cool, they are offered in a flexible bond that can easily follow contoured surfaces for the light grinding and blending of MIG and TIG welds on tanks and vessels in one step.

Capable of producing a 32 RMS finish on stainless steel and non-loading on aluminum, Rex-Cut Cut-N-Finish Discs will last up to 20 times longer than flap- and resin fiber discs, claims the firm. Available in flexible and medium bonds with A24, A36, A54 and A80 grit sizes, these discs come in 4”, 4-1/2” and 7” dia. sizes. They are also suitable for flat surfaces.

Rex-Cut Cut-N-Finish Discs are priced according to grit, size and quantity. Literature and pricing are available upon request.

For more information, visit www.rexcut.com,

You May Also Like

Pulling Codes: Multiple Misfire Personalities

A vehicle fails an emission test due to a series of codes, with misfire activity found on cylinders 2, 4, 6, 8 and 3 – and a strange metallic sound can be heard when the rpms are raised. See how Carlton Banks solves this latest Pulling Codes case.

A Story of Codes P0302, 04, 06, 08 & 03
 

This month’s diagnostic journey begins with a 2008 Land Rover Discovery that is taken in to a local testing facility for an emission test and fails due to a series of misfire codes.

Misfire activity is found on cylinders 2, 4, 6, 8 and 3; at first glance this series of codes implies that there may be bank 2 issues, but the cylinder 3 code throws a wrench into that mode of thought.

Using Volumetric Efficiency to Determine the Health of an Engine

Using an OBD II scan tool/dynamometer simulation/calculation program that can graph volumetric efficiency (VE) over rpms, contributor Glen Beanard devised a test sequence using real-world vehicles. This article takes you step by step through his diagnostic process.

Intermittent Engine Misfire Analysis

Even for an experienced diagnostic technician, attempting to diagnose an intermittent misfire condition that occurs only under specific driving conditions can be a frustrating exercise. Contributor Gary Goms breaks it down, and includes tips for using a scan tool and a lab scope.

5 Mistakes Newbie Tire Techs Make

Nothing can turn a new tech into a veteran but time and experience, and often that experience is going to come from making mistakes – sometimes real bad ones – and learning from them (you hope). By addressing these most common mistakes right away with new tire techs, the worst of them can be avoided.

Rivet Bonding Comes Full Blast

Now that rivet bonding is in the mainstream with the Ford F-150, it’s time for shops to look into training and equipment for this repair process.

Other Posts

‘Test Before Touch’ – It’s No Waste of Time

To help reduce the headaches involved in servicing TPMS, it’s important to use the “Test Before Touch” procedures in your shop. Used properly, TBT can form a strong foundation for everything else you do regarding TPMS, reduce complexity and help you educate and keep your customers.

The Right Diagnostic Tools Save You From Extensive Disassembly Time

It can sometimes be difficult to make the correct diagnosis for a hard-to-start complaint. And diagnostic time may be extensive — and expensive. This article shows how certain tools have the ability to automatically analyze waveforms for you.

Know the Specs for Your Social Media Accounts

If you’re doing social media, are you doing it effectively? Are your accounts set up correctly? Are you posting often enough? Mark Claypool answers some questions.

Top 5 Tools: Kenny Younkins, Ken’s Auto Service Center

Kenny Younkins, owner Related Articles – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set – Mayhew Debuts New Fluorescent Handled Screwdrivers Ken’s Auto Service Center Akron, OH While Ken first said his favorite tool is his fishing rod, he said in the shop he prefers these five: