Rotor Runout: Cause and Correction

Rotor Runout: Cause and Correction

The vehicle owner may say that under light braking the vehicle pulses to a stop or under heavy braking the vehicle shudders. Technical service bulletins (TSBs) often describe these symptoms as a “judder.” There are only two causes for judder — lateral runout and disc thickness variation on the rotor’s friction surface.

What could have caused the lateral runout? The causes of the condition range from lugs that were over or unevenly torqued to common corrosion between the hub and rotor.

There are other causes, such as the rotor machined to less-than-minimum thickness and overheating. Correcting the condition requires the machining or replacement of the rotor. Whether you are turning a rotor on or off the vehicle or replacing it, preparation is the key to success.

The greatest cause of lateral runout comebacks is not poor OEM engineering or low-quality aftermarket parts, it is ignorance and carelessness. Don’t take this the wrong way, but some of your instincts and methods of operation could be costing you. By no means, is this written from from the perspective of talking down to the technician, it is just some self-introspection can even help the best technician. Take the time to perform a diagnostic on yourself. You might be surprised.

You are Only as Good as Your Tools
Both on-the-car or off-the-car brake lathes are precision machines that that must be maintained and treated with great care. Dirt and metal chips can shorten the life span of any lathe and lead to comebacks.

When was the last time you checked the runout of the arbor and cutting head? Remember, the cut is only as true as the arbor, spindle and adapters.

Some of the TSBs contain information on checking runout of the lathe arbor and clamps. But, your best source of information is the manual that came with the lathe. If you can not find it, it may be online in PDF format. Even if your bench lathe is as old as dirt, someone can sell you the parts to fix it.

Look at the condition of your adapters. A weekly cleaning and lubrication should be performed. The adapters should be trued to the arbor on a monthly basis. After they are trued, all nicks and burrs should be removed with a fine emery cloth. Coat the adapters with a light coat of oil.

What about cutting bits? This topic is an article on its own. For some techs, proper cutting bit care is just as difficult as putting the toilet seat down or putting a new roll of toilet paper back on the roller.

On-the-Car Runout
Today, you can purchase an on-the-car brake lathe that, after it has been attached to the vehicle, will automatically properly compensate for runout. It is quick and easy.

But, wait a minute, most manufacturers have written extensive bulletins on the proper methods of turning brake rotors. All of the bulletins begin with the proper preparation and measurement of the components before turning the rotor. Most dealers are required to have a runout compensating on-the-car brake lathe by the OEMs, and the OEMs are paying the warranty time. So why would they begin a TSB with this “extra” check before turning the rotor? Simple, it is a quality check that helps to eliminate runout problems that could actually be made worse by turning the rotor.

Turning a rotor is a precision operation that requires a clean and rust-free mounting surface. There are tools available to clean the bearing flange and rotor mounting surfaces. They can range from rotating abrasive to hooded sandblasters. Vented rotors can be a source of rust that can range from dust to chunks coming from the vent passages. It is a good idea to knock loose the rust with a wire brush to prevent it from getting on mounting surfaces and turning equipment.

Once the rust has settled, pull out your dial gauge and go to work. The arbor of a bench lathe is essentially the wheel bearing when cutting on-the-car. The maximum endplay for a bearing is 0.004” (0.100 mm). This is a good reason to check flange runout and endplay before installing the lathe adapter.

The wheel bearing is the heart of the assembly. If the bearing flange has a runout, that runout will be magnified at the rotor friction surface. A runout of 0.0005 inch (0.00254 mm) at the bearing flange could result in a 0.001 inch (0.025 mm) runout at the rotor friction surface. The maximum allowable runout at the rotor friction surface is 0.002 inch (0.050 mm) as stated by most manufacturers.

Shimming the Rotor
Flange runout can be corrected with tapered shims that are available to correct a runout of 0.003inch (0.075 mm) to 0.009 inch (0.230 mm) A runout of more than 0.005 inch (0.125 mm) at the bearing flange cannot be corrected by the use of a shim. The combination of rotor and bearing flange could prevent the rotor from being turned. Checking bearing flange runout should be performed after friction surface runout. Changing the rotor position 180º on the bearing can check flange runout. If the high spot changes 180º, the rotor could be OK or ready to turn after the bearing is shimmed.

Components should be marked as you perform an inspection of the assembly. Check the bearing endplay. Mark the relation of the rotor to the bearing flange. Mark the rotor high and low runout spots on the rotor friction surface. The low spot marked as zero and the high spot as 0.XX”. Mark the high and low runout spots on the bearing flange with the same method and the rotor friction surface.

Once you have collected the data, the following comparisons should be made. If the endplay exceeds manufacturer’s specifications, replace the bearing and recheck runout. Compare bearing flange to rotor runout position. If the shim cannot correct the runout, the bearing should be replaced. Check the rotor thickness. The minimum dimension should be stamped or cast into the rotor. There has to be enough thickness to cover the runout without going below the minimum thickness.

Hub and Rotor Interaction
How the rotor interfaces with the hub can determine runout. Think of the rotor as the peanut butter in a peanut butter and jelly sandwich and the hub and wheel as the slices of bread. If you push down on one corner, the peanut butter will shoot out the opposite corner. If you tighten lug nuts in a circular pattern, stress is placed on the rotor hat section and bearing flange unevenly.

All wheels should be mounted by using a crossing pattern to tighten the lugs.

Pulling it Together
Most knowledge and learning for technicians about trueing rotors is picked up in bits and pieces from various sources and failures. It is learning with don’ts and very little do’s. Below, is a list of how it should be done for installing new rotors and machining old rotors.

Installing New Rotors

  1. Check bearing end play: End play is an indication of bearing condition and adjustment.

  2. Clean the bearing flange: Surface should free of debris for a good dial indicator reading.

  3. Check bearing flange runout: Flange run out is magnified at the rotor friction surface.

  4. Install new rotor: Torque the rotor on the flange to check alignment to the knuckle.

  5. Check new rotor runout: It’s a double check before installing the wheel.

Turning Rotors (off vehicle)

  1. Check lateral runout: mark high and low spot, a shim maybe required to correct the runout.

  2. Check rotor thickness: Compare to runout for minimum thickness before and after turning.

  3. Clean the bearing flange.

  4. Clean the rotor to bearing mounting surface.

  5. Check bearing end play: should be no more than 0.004 inch (0.100mm).

  6. Check bearing flange runout: change rotor position on bearing.

  7. vehicle.

  8. Check turned rotor runout and thickness: it’s a double check before installing the wheel.

Turning Rotors (on vehicle)

  1. Check rotor thickness.

  2. Check bearing end play.

  3. Check lateral runout.

  4. Clean wheel and rotor mounting surface.

  5. Mount lathe according to manufacturers instructions.

  6. Machine the rotor.

  7. Check turned rotor runout and thickness.

The steps above may look simple, but used as a frame work for basic brake repair they can go a long ways to ensuring quality and reducing comebacks.

But, a recent General Motor’s TSB takes it to the next level. The bulletin makes two critical points:

GM Bulletin 00-05-002D:
If performing routine brake service for worn pads only, and the rotors are not damaged and measure within specification, DO NOT REFINISH ROTORS.

  • Remove the old rotor(s).

  • Measure the rotor for original thickness using a brake micrometer.

  • Reference the minimum thickness specification stamped on the backside of the rotor or SI for Minimum Thickness specification/other. In most cases, the rotor should be refinished unless the measurement taken makes it obvious that refinishing the rotor would take the measurement under the Minimum Thickness specification (then replacement is necessary).

  • Record the ORIGINAL rotor thickness measurement on the repair order hard copy.

  • Clean all of the mating surfaces between the hub, the rotor and the wheel using the J 42450A — Wheel Hub Cleaning Kit if rotors are not to be refinished.

Important: Cleaning all mating surfaces and making them free of corrosion, burrs and other debris (which includes removal of Hubless rotors) is critical and MUST be performed whether using an On-Car or Bench Lathe Refinish Procedure.

Be sure to follow the appropriate refinishing procedure listed below for the type of lathe you are using.

Important: Only replace the rotors if they do not meet the Minimum Thickness specification.


Important: Only remove the necessary amount of material from each side of the rotor and note that equal amounts of material do not have to be removed from both sides on any brake system using a floating caliper.

Important: Prior to making the cut, install the recommended clip-on style disc silencer supplied with the lathe. Use of this silencer is critical to prevent chatter from occurring during the cut.

There is an old saying “No preparation leads to poor performance. Brakes are one of the most important safety systems on the vehicle.

You May Also Like

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah

Remember last month how I said 2024 was your year to be the technicians you always wanted to be? Remaining stagnant as a technician is simply not an option anymore if you want to be successful in the automotive industry. You must proactively seek out opportunities to embrace new tools, techniques and solutions that promise to enhance efficiency, accuracy and customer satisfaction.Embracing what’s new is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.One of the top reasons I can give you for embracing new technology is the potential for improved diagnostic accuracy and efficiency. With the arrival of advanced diagnostic tools, like the Bosch ADS 625X, the Autel IA900, or the Hunter ADASLink, technicians can pinpoint issues with precision, reducing guesswork and minimizing the risk of a comeback. Whether it’s sophisticated tools or cutting-edge software solutions, the ability to leverage these new tools should empower you to deliver next-level service and drive positive repair experiences for your customers.Another thing to keep in mind is that embracing new technology and equipment opens doors to expanded service offerings. From state-of-the-art lifts and alignment systems, to specialized tools designed for specific makes and models, investing in the latest equipment enables you and other technicians to tackle a larger range of repairs and maintenance with confidence and precision. As the technology in cars continue to evolve, so too must the tools and equipment that technicians rely on to get the job done.Embracing new technology and equipment can also lead to improved productivity in the shop. By leveraging high-quality products that are specifically designed for today’s vehicles, you can streamline workflow, minimize downtime and deliver exceptional results for your customers.At TechShop, we understand the importance of embracing new technology, equipment and products in the automotive repair industry. That’s why we’re excited to announce the debut of our all-new “Tool Time” video podcast series, where guests from brands like Ingersoll Rand, Clore Automotive, SATA Spray Equipment and many more will sit down and join Eric Garbe and myself to discuss education and training on the latest products our industry has to offer.Join us as we embrace the future of automotive tool supply and equipment advancements together. And, be sure to subscribe to the TechShop newsletter to stay tuned!

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Lisle 61860 Oil Filter Housing Torque Adapter – Mueller Kueps Presents Redesigned Sensor Tap Series – Lisle Low Profile Fuel Line Disconnect   OTC Genisys Touch – Quick scan, bidirectional control Snap-on VANTAGE Pro –

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool
2024 Is Your Year to Be the Technician You Always Wanted to Be

As we enter 2024, strategic career planning is essential for success in the automotive repair industry.

happy new year 2024
Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.