Tech Feature: Brake Job on 2004-2008 Toyota Corolla

Tech Feature: Brake Job on 2004-2008 Toyota Corolla

The 2004-2008 Toyota Corolla was one of the best selling vehicles in North America. The front brakes for all models are, for the most part, the same. The only changes came in the configuration of the brake pad shims. The Corolla was not subject to the unintended acceleration recalls for floor mats or gas pedal.

2004-2006 models can have either drum or disc. 2007-2008 models all have drums.

No official explanation could be found for the change. Some say it was due to better ABS systems. While others say it was to simplify production.

Looking at the TSBs from Toyota’s website, these are relatively trouble free with no recalls for the brake system. While these vehicles are not prone to abnormal brake noise, Toyota advises in TSBs that technicians should pay attention to hardware and shims when performing a brake job.
 
Front Brakes
1. Remove the caliper slide pin bolts.

2. Pull the caliper and hang it from the strut. Inspect the piston boot for any damage.

3. Remove the outer pad and push back the piston with the appropriate tool. You can restrict the brake hose with a non-damaging tool and relieve the pressure through the bleeder. However,  Toyota does not recommend this procedure.

4. Remove the inner pad. If the pads are original, it will have a two-piece shim on each pad. Make a note of the positions of all four shims and clips.

5. Using a ruler, measure the pad lining thickness. Maximum thickness: 11.0 mm (0.433”) and minimum thickness: 1.0 mm (0.039”).

6. Remove the bolts that hold on the caliper bracket.

7. Inspect caliper bracket for damage and corrosion.

8. Measure the pad thickness. The standard thickness is 25 mm (0.984”). The Minimum thickness: 23 mm (0.906”).

9. Make “matchmarks” on the front disc and the axle hub. Fasten the disc with hub nuts. Torque to 103 n/m 76 ft/lbs.

10. Measure the rotor’s runout 10 mm away from the outer edge of the disc. Toyota specifies a maximum disc runout 0.05 mm (0.0020 in.). If the disc runout is the maximum value or greater, check the bearing play hub flange runout.
Tip: You can lower the runout by changing the position of the rotor on the hub flange. With this technique you can minimize the amount of material removed from the rotor during on-the-car machining. This can make a more thermally stable rotor that absorbs heat evenly and reduces pulsation comebacks.

11. Place caliper bracket in a vise. Clean the bracket and replace the abutment clips if necessary. You can also apply a moly-based lubricant to the surfaces that make contact with backing plate of the brake pad. It is recommended that the slides and bushings in the bracket be replaced if the rubber or metal has degraded. To remove or install the pins, Toyota recommends using a socket (19 mm) and hammer to drive the dust boots into the disc brake cylinder mounting. Apply the lithium or silicone base lubricant to seal the surface of slide pin’s dust boots.

12. Install the caliper bracket and torque the bolts to 106.8 n/m or 79 ft/lbs.

13. Install the pads. Depending on the type of shim used on the new brake pad, lubricate the recommended areas as indicated by the manufacturer. Do not reuse the old shims. Note: Install the pad wear indicator plate facing upward.

14. Install caliper. Torque the two bolts to 34.3 n/m or 25 ft/lbs.

15. Torque the lug nuts to 103 n/m or 76 ft/lbs.
Note: If the caliper was replaced, the torque for the union bolt is 29 n/m or 21 ft/lbs. Always install a new copper washers with the union bolt.

Rear Disc Brakes
1. Remove the clip, anti-rattle spring no.1 and anti-rattle spring no.2.

2. Remove the pad guide pins and disc brake pads and shims.

3. Remove caliper bolts that hold it to the knuckle.

4. Push back the piston with the appropriate tool. Do not use force to screw the piston into the disc brake cylinder. You can restrict the brake hose with a non-damaging tool

and relieve the pressure through the bleeder. But, Toyota and GM do not recommend this procedure.

5. Remove the bushings and slides from the caliper assembly so they can be replaced or cleaned and lubricated.

6. Using a ruler, measure the pad lining thickness. Standard thickness: 10.0 mm (0.394”)  and minimum thickness: 1.0 mm (0.039”) .
7. Inspect rotor thickness. Standard thickness: 9.0 mm (0.354”) and minimum thickness: 7.5 mm (0.295”)

8. Measure the disc runout 10 mm away from the outer edge of the disc.
Maximum disc runout: 0.05 mm (0.0020”). If the disc runout is the maximum value or greater, check the bearing play in the axial direction and check the hub flange for runout. Also, you can lower the runout by changing the position of the rotor on the hub flange. With this technique you can minimize the amount of material that is removed from the rotor. This can make a more thermally stable rotor that absorbs heat evenly and can reduce pulsation complaints.

9. Install the rotor.

10. Install slide boots. Apply the lithium- or silicone-based grease to sealing surfaces of the boots. Place the caliper on over the rotor and install the mounting bolts and torque to 46.6 n/m or 34 ft/lbs.

11. Install the pads and shims. Depending on the type of shim used on the new brake pad, lubricate the recommended areas as indicated by the manufacturer. Do not reuse the old shims.

12. Install the two guide pins to the brake pads.

13. Install spring no. 1.
(a) Hook the spring upper portion to the guide pin no.1.
(b) Hook the spring lower portion to the center hole of the pad.
14. Install spring no. 2.
(a) Hook the spring upper portion to the guide pin no. 1.
(b) Hook the spring lower portion to the center hole of the pad.
15. Fix guide pins with clip
(a) Insert the clip end into the hole of the guide pin no. 1.
(b) Insert the other clip end into the hole of the guide pin no. 2.
The clip should be fully inserted into the guide pin no. 1 and No. 2. If not, the guide pins will come off and the caliper will be damaged when the brakes are applied.

Adjusting Rear Drums

1. Perform this adjustment with the wheel off.

2. Remove the hole plug, and turn the adjuster and expand the shoe until the drum locks.

3. Using a screwdriver, back off the adjuster eight notches.

4. Install the hole plug.

5. Normal brake actuation will bring the clearance into optimal adjustment.

Adjusting the Parking Brake

1. Pull the parking brake lever to the fully applied position, and count the number of clicks. The parking brake lever should travel five to eight clicks with a moderate pulling force.

2. To adjust, remove the rear console box sub-assembly.

3. Loosen the lock nut and turn the adjusting nut until the lever travel is correct.

4. Tighten the lock nut to 5.0 n/m or 44 in/lbs.

Bleeding

The Corolla can be bled conventionally. But, if the ABS modulator/actuator has been replaced or the pedal is still soft or low, it will require a scan tool to bleed the system. Just remember to depress the brake pedal more than 20 times with the engine off to let the vacuum pressure out from the brake booster assembly before bleeding. 

You May Also Like

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion

The corporate world has offices. You hang pictures on the wall, keep a few trinkets on your desk and a few snacks in one of your desk drawers. It’s your space. As technicians, we have our toolbox. It’s our “office” on wheels. But it’s different. We have no “work from home” option. We can’t take it with us and work at a coffee shop. Our “office space” becomes far more important. This is where we make our living.The size of a toolbox and the features we choose depend on multiple factors, which have changed over the years along with automotive and tool technology. Here’s a look at some of the core features and modern frills to consider when it’s time to move into a new office.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

#2 Calipers & Micrometers

Calipers and Micrometers are essential measuring tools when exact precision is required.

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread