Tech Feature: Getting The Most Data From Your Scan Tool

Tech Feature: Getting The Most Data From Your Scan Tool

It's more than likely that many technicians use their scan tools as diagnostic trouble code (DTC) readers rather than as the analytical and testing tools that they really are.

08 and european.”/>

Next, I entered Chrysler’s actuator test mode (ATM), which is a bi-directional feature used to activate or “buzz” the fuel pump, fuel injectors, ignition coils and other engine management system components. All of items on the ATM list activated correctly with the exception of the three waste-spark ignition coils. I couldn’t get spark from any of the front engine bank spark plug wires by activating the coils.

The primary ignition coil circuit on a 1996 3.3L Chrysler product is fairly simple. Battery voltage is supplied to the ignition coil primary circuits by the auto shut-down (ASD) relay when the PCM activates the ASD during cranking or running or during an ATM test. The PCM creates a spark by using a coil driver to ground the primary circuit to saturate the coil’s primary windings and then by breaking the coil primary circuit to create a high-voltage spark in the secondary circuit.

Because I had battery voltage at the B+ and B- primary coil terminals, it was easy to assume that either the CKP wasn’t signaling the PCM to ground the ignition coil primary circuits or the PCM itself wasn’t grounding the coils.

Because the PCM had been replaced at least three times with no result, I used the Module Identification feature of my aftermarket scan tool to verify that the vehicle had the correct PCM installed.

it’s important to poll each of these modules for diagnostic trouble codes and correct communications.

According to the scan tool’s Module Identification mode, the module was designed for “a 1997 Dodge 3.0L engine.” The fact that the PCM was designed for a 3.0L engine using a distributor-type ignition as opposed to a PCM designed for a 3.3L engine using a distributorless ignition did, indeed, explain why the engine had a spark-related cranking, no-start complaint. Oddly enough, the PCM’s data stream showed the camshaft and crankshaft sensors working perfectly, even though the PCM was a mismatch for a distributor-type and distributorless ignition.

Because the original computer had been returned for its core charge and because the 3.3L cores are becoming increasingly rare, the Dodge Caravan is now waiting for another rebuildable core. But the point remains that what first appeared to be an incredibly difficult diagnostic dilemma was solved relatively quickly and easily by using an aftermarket scan tool to determine that the last replacement PCM didn’t match the application.

Aftermarket Scan Tools
While many master technicians are now using original equipment (OE) scan tools to diagnose modern onboard electronics, suffice it to say that most professional-grade aftermarket scan tools still have the diagnostic capacity needed to solve the majority of electronics failures passing through an average independent repair shop. In brief, aftermarket scan tool manufacturers condense information supplied to them by OE tool manufacturers into menus designed to address the most common failures occurring in the most common vehicle platforms. The depth of coverage and diagnostic capability varies according to the vehicle application and the information-handling capacity of the scan tool itself.

if inaccurate vin information is entered or the wrong cable adapter is used, the scan tool may not communicate with the pcm or the resulting information may not be reliable.

Many aftermarket manufacturers also enhance the diagnostic capability of their scan tools by including technical hotline information, empirical or anecdotal information, engine testing and adjustment specifications, and OE technical service bulletins into their databases. When choosing an aftermarket scan tool, keep in mind that many are specifically designed for the domestic, European or Asian markets. Some, for example, concentrate on Mode $06 diagnostic information, while others concentrate on building a user-friendly format or extensive diagnostic database into their scan tools. Although most aftermarket scan tools are still produced in self-contained, updatable platforms, others are produced as PC-based software systems with cords and adapters needed to interface with vehicle data link  connectors (DLCs).

Vehicle Identification
Because aftermarket scan tools have such a diversity of platforms and formats, I’ll use a Snap-on Solus Pro scan tool to illustrate the following installments of “Getting The Most Data From Your Aftermarket Scan Tool” in the most cohesive manner possible.

to allow faster updates, each of these serial data lists displays specialized  powertrain information.

In general, the first menu displayed on an aftermarket scan tool has to do with correctly identifying the vehicle. When entering the “Global OBD II” or “generic” menu, keep in mind that it isn’t necessary to enter the Vehicle Identification Number (VIN). If Global OBD II is used, remember that the Global or generic diagnostic system is universally adapted for diagnosing emissions-related failures in all makes and models of vehicles and therefore does not have the overall diagnostic capability of the enhanced or “OE-style” diagnostic mode. Nevertheless, the Global OBD II mode may display freeze-frame and other data that may not be included in the scan tool’s enhanced mode.

When entering the “enhanced” or “OE” diagnostic mode, the VIN must be entered manually unless, of course, the scan tool automatically enters the VIN. If the vehicle’s VIN has been previously entered into the scan tool, the application may be found in the “existing” or “previous” vehicle menu. After the VIN is entered, the next menu might ask the vehicle’s gross weight or if the vehicle is equipped with an air pump, manual or automatic transmission, or air conditioning. Last, the menu might specify a “personality key” or cable insert that adapts the scan tool cable to the vehicle’s OBD II diagnostic connector.

Module Communications
Because most current domestic vehicle models have at least four onboard modules (PCM, ABS, air bag, anti-theft, etc.) make sure the scan tool will communicate with each module before proceeding with a diagnosis.
Although aftermarket scan tool manufacturers are increasing their capacity to communicate with body control modules, keep in mind that because a module isn’t listed on the menu of an aftermarket scan tool doesn’t mean the module doesn’t exist. It simply means that the aftermarket scan tool won’t communicate with the module.
If you’re in doubt, attempt communicating by using another brand of aftermarket scan tool. In still other cases, the adapter key or insert must be changed before the scan tool will communicate with a specific module. Last, always poll each module for any diagnostic trouble codes. In some cases, these codes may influence the course of your diagnostic strategy.

After opening the generic functions menu, notice that the “Generic OBD II Function” mode menu is listed in hexadecimal numbers. Mode $09 will allow access to the module calibration and the vehicle VIN. The VIN  displayed on the screen should match the VIN of the vehicle.

When reviewing diagnostic trouble codes, remember that “P” is the prefix for powertrain codes, “B” is for body control codes, “C” is for chassis-related codes like ABS, and “U” is for network or data link communications codes.

To further illustrate, the zero following the “P” in a P0122 DTC indicates a “global,” “generic” or “SAE” DTC. If the “P” is followed  by a “1” (ex. P1122) the DTC is a manufacturer-specific or enhanced code that may have a vehicle-specific definition. The second digit, number “1,” indicates the system (fuel/ air metering) and the third digit indicates the component and the type of failure being experienced (Throttle Position Sensor Circuit Low Voltage).

Serial Data Screens
The term “serial data” refers to a data stream being composed of a series of data bits, with each bit representing a specific type of data. Because of its structure, a serial data stream doesn’t instantly report a change in a specific value. Instead, we have to wait until the data stream updates itself before we can see the new data.

Because each line on a serial data screen must be continually updated, modern scan tools increase the update rate reducing the number of data lines per screen by dividing the data up into smaller screens. If, in the following photo, the O2 sensor screen is selected, the reduced number of data lines will permit faster numerical updates on oxygen sensor data.

Module Identification
In my opening case study, I mentioned the importance of identifying the module before beginning a diagnosis. On the Solus Pro scan tool, the module calibration numbers and VIN can be accessed through the main menu under “generic functions.”

Practice, Practice, Practice
Because there are literally thousands of scan tool menu formats in the current marketplace, it’s important for you, the technician, to get the most from your aftermarket scan tool by navigating through the menus. You’ll find that auto manufacturers may change their formats with each new vehicle introduction, and you might subsequently see considerable differences in menu formats and operational features from model year to model year.
In the next installment, we’ll look at how to use features like movie record, data graphing and other components of the modern aftermarket scan tool to diagnose no-code, random and intermittent component failures in modern engine management systems. Until then, spend a few extra minutes each day navigating your aftermarket scan tool. The reward will be increased diagnostic accuracy and reduced comebacks on diagnostic repairs. 

NOTE: For Part II of Gary’s article, click here: http://www.underhoodservice.com/Article/68368/acquiring_data_on__scan_tools_part_ii.aspx

You May Also Like

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion

The corporate world has offices. You hang pictures on the wall, keep a few trinkets on your desk and a few snacks in one of your desk drawers. It’s your space. As technicians, we have our toolbox. It’s our “office” on wheels. But it’s different. We have no “work from home” option. We can’t take it with us and work at a coffee shop. Our “office space” becomes far more important. This is where we make our living.The size of a toolbox and the features we choose depend on multiple factors, which have changed over the years along with automotive and tool technology. Here’s a look at some of the core features and modern frills to consider when it’s time to move into a new office.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
PRT Launches 22 New Products on Complete Strut Assemblies

The new items come to expand the PRT portfolio in North American Market and represents more than 12 Million vehicles in new coverage.