Tech Feature: Why Aftermarket Belts are Lasting Longer

Tech Feature: Why Aftermarket Belts are Lasting Longer

Serpentine belts made of EPDM may last up to 100,000 miles or more before they have to be replaced. But that doesn't mean they will last forever. A serpentine belt that's aging or slipping may develop a hard glazed surface that makes the belt noisy. Aerosol belt treatments may quiet the noise for a while, but sooner or later you'll have to replace your customer's belt.

There was a time when rubber belts were maintenance items that had to be replaced every five or six years, depending on their condition.

The original equipment belts on today’s late-model vehicles are mostly made of EPDM (ethylene propylene diene monomer), a synthetic rubber that is far more durable, heat-resistant and wear-resistant than Neoprene. This means serpentine belts made of EPDM may last up to 100,000 miles or more before they have to be replaced. But that doesn’t mean they will last forever.

A serpentine belt that’s aging or slipping may develop a hard glazed surface that makes the belt noisy. Aerosol belt treatments may quiet the noise for a while, but sooner or later you’ll have to replace your customer’s belt.
The appearance of surface cracks in the rubber is another clue that a belt is reaching the end of the road and should be replaced — the sooner the better because a belt failure will result in a breakdown (loss of engine cooling, A/C cooling, charging output and power steering assist).

Belt noise and/or premature wear is often the result of a bad automatic tensioner. Customers should be advised to check their belt tensioner if a serpentine belt is making noise, slipping or fluttering when the engine is revved. High-mileage tensioners often have weak springs and can stick if there is corrosion in the pivot bearing. A special tool is often needed to rotate the tensioner so the belt can be replaced.

Can’t find the automatic belt tensioner? Some late-model engines don’t have one. Instead, they use a new type of “Stretch Fit” serpentine belt. Such belts have special polyamide tension cords inside that allow the belt to stretch slightly (like a rubber band), but in a controlled way so belt tension is maintained without the need of a tensioner. Ordinary serpentine belts do not stretch, and must use a tensioner or have some type of adjustments on the belt-driven accessories.

Though ordinary replacement serpentine belts must be the exact same length as the original to fit properly, stretch fit belts are actually slightly shorter than the original belt. Installation requires routing the belt around all of the pulleys, then stretching it over the last pulley with a special tool.

Applications for the new stretch fit belts include 2004 and newer Mazda MPV and Tribute 3.0L, 2005 and newer Ford Escape 3.0L, 2006 and newer Ford Fusion 3.0L, 2008 Ford Taurus 3.5L, 2007 and newer Chrysler Sebring and Dodge Stratus 2.7L, 2007 and newer Dodge Nitro 4.0L, 2008 and newer Chevy Silverado and GMC Sierra trucks, and 2008 and 2009 Hummer H3.

The new stretch fit belts are not designed to replace ordinary serpentine belts on older vehicles. They must only be used on newer vehicles that are designed for them. Likewise, an ordinary serpentine belt should not be used in an application that requires a stretch fit belt. Attempting to stretch an ordinary serpentine belt over a pulley can damage the cords inside it and cause the belt to fail.

Something else that’s new is the use of overrunning alternator decouplers (OAD) on a growing number of late-model vehicles, including Chevrolet Corvette, Camaro and HHR, Buick Lucerne, Cadillac CTS and Escalade, Volvo XC60 and XC90, and various Lexus, Scion and Toyota models.

OADs (also referred to as isolating decoupler pulleys, or IDPs) help enhance engine efficiency and reduce noise, vibration and harshness. Using any other type of replacement pulley on an alternator, such as a one-way clutch, isolating pulley or solid pulley, on an application that came originally equipped with an OAD pulley can lead to customer complaints about noise and vibration, as well as premature belt failure.

Finding a Failing Belt
Most belts fail from the inside out. Belts deteriorate with heat and mileage. Every time a belt passes around a pulley, it bends and flexes. This produces heat in the belt, which hardens the rubber over time. The wear process can be greatly accelerated if the belt is loose and slips. The additional friction between the belt and pulley will make a belt run even hotter.

After millions of such journeys around the pulleys, even the best drive belt begins to suffer the effects of age. The rubber begins to crack and fray, and the internal cords become weakened and
brittle. Eventually the belt breaks, and at that point, all cooling is lost along with whatever other functions were powered by the belt.

You can’t always determine a belt’s true condition by appearances alone. Any belt that is obviously cracked and frayed should be replaced. But with many of today’s “bandless” belts, there is no outside cover to peel loose and betray the belt’s deteriorated condition. A belt may appear to be like new on the outside yet be on the verge of failure because of weakened cords inside.

Contaminants in the drive system will cause belt damage and premature wear. So make sure the grooves are clean and not fouled with dust, dirt, grease, rocks, etc.

Small and packed debris will prevent the belt from properly seating in the groove and detract from power transmission capability. Fix all lubricant and coolant leaks. Lubricants will reduce the coefficient of friction between the belt and pulley, inducing belt slippage, and eventually will attack the rubber compound. Coolant increases the potential for the belt to make noise.

Also, look for any glazing (shiny) on the underside of the belt indicates that the belt has been slipping. A slipping belt is bad news for a vehicle’s belt drive system.

Remember, some cracks on the underside of a serpentine belt are normal with age. But with EPDM constructed belts, if more than three cracks are counted in a 3” section on any one rib, the belt has already used up 80% of its intended life, and should be replaced. 

You May Also Like

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion

The corporate world has offices. You hang pictures on the wall, keep a few trinkets on your desk and a few snacks in one of your desk drawers. It’s your space. As technicians, we have our toolbox. It’s our “office” on wheels. But it’s different. We have no “work from home” option. We can’t take it with us and work at a coffee shop. Our “office space” becomes far more important. This is where we make our living.The size of a toolbox and the features we choose depend on multiple factors, which have changed over the years along with automotive and tool technology. Here’s a look at some of the core features and modern frills to consider when it’s time to move into a new office.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
PRT Launches 22 New Products on Complete Strut Assemblies

The new items come to expand the PRT portfolio in North American Market and represents more than 12 Million vehicles in new coverage.