Tech Tip: Causes of Melted Piston Top and Ring Land on Diesel Engines

Tech Tip: Causes of Melted Piston Top and Ring Land on Diesel Engines

Engine damage resulting in melted piston tops and ring lands may be found in several stages outlined in this bulletin, ranging from light damage at the piston to catastrophic engine failure.

Engine damage resulting in melted piston tops and ring lands may be found in several stages outlined in this bulletin, ranging from light damage at the piston to catastrophic engine failure.
Figure 1: Melting at the top land of a diesel piston.
Signs of melted piston or ring land damage include:

• Erosion at the piston crown is visible. 

• Melted areas can be seen at the piston crown (Fig. 1) – right up to a completely melted off top of the piston (Fig. 2). 

• In extreme cases, there are seizure marks all along and around the piston. There is a hole in the piston. 


PROBABLE CAUSES 

This damage is attributed to the thermal overload of the piston.
There are two causes for this. 



Abnormal combustion can be diagnosed via the following features: 

• The bowl edge has been “gnawed off.”

• The injection nozzles display a poor spray pattern. 

• The injection pressure and the delivery rate of the injection nozzles are set incorrectly. 

• The top land shows seizure marks in the piston pin axis. 


Figure 2: Melted piston crown at a diesel piston.
An abnormal combustion can be caused by a number of factors such as if the air-fuel mixture in the combustion chamber is too rich. This can be the result of the following: 

• The air supply is reduced, e.g. the air filter is clogged. 

• The fuel delivery is set incorrectly. 

• The start of fuel delivery is set incorrectly. 

• The nozzle needle is either wedged or stiff. 

• The exhaust gas system is clogged. 
 


There is ignition delay and misfiring, which may be caused by: 

• The incorrect fuel or fuel with an insufficient cetane rating is being used, or there is gasoline in the diesel. 

• The valves are leaky, resulting in compression loss. 

• The protrusion is too small (i.e., there is insufficient compression). 

• The air pre-warming is defective (especially for very low ambient temperatures). 



Overheating of the piston crown can be identified via the following features: 

• The combustion bowl is not damaged. 

• An excellent spray pattern can be observed at the top of the piston. 



The excessive temperature level of the piston crown can be caused by: 

• The cooling oil nozzle is either bent, has become detached or has not been assembled (assembly error). 

• The time between oil changes is too long. In this case, there is a risk of polymerization of the engine oil, especially when using biofuels, such as rapeseed and soybean oil, which can result in the cooling oil nozzles being clogged. 

• Contamination, such as gasket residue, etc., prevents the required circulation in the oil circuit. 



SOLUTION

• Set the injection amount and timing according to the manufacturer’s specifications. 

• Check the injection nozzles for any leaks, the injection pressure and the spray pattern. 

• Pay attention to correct alignment when assembling the cooling oil nozzles. 

• Thoroughly clean the oil channels in the engine block, the crankshaft and the cylinder head. 

• Make sure the pressure-regulating valve is functioning correctly. 

• Ensure that the time between oil changes is much shorter when running the engine on biofuels. 



Tech Tip courtesy of MAHLE Clevite.

You May Also Like

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Technology is defined as the application of scientific knowledge for practical purposes, especially in industry. We often picture technology as something that has computers and electronics attached, and often it does. But, in the world of impacts, both in the realm of pneumatic and cordless, technology bears much deeper roots.

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter
More Than A Scan Tool

Scan tools serve as indispensable diagnostic hubs, offering access to a wealth of resources, from OEM technical bulletins to community-documented repairs.

scan tool
Battling Stress and Burnout

Here are some quick tips for managing stress and avoiding burnout in the fast-paced automotive repair industry.

Nadine Battah

Other Posts

EV Acronyms and Terminology

Electric vehicles (EVs) are here to stay and there’s a lot to learn.

EV
The Value of Honesty in Auto Repairs

Discover how a simple act of returning found money led to a radio story, highlighting the significance of honesty.

Diagnosing Electrical Problems With Your Multimeter

Transform your electrical diagnostics with these routine multimeter tests.

Multimeter
Elevating Your Career: Mastering Customer Service Skills

Here are some key customer service skills that can elevate your career in the industry.

Photo of Nadine Battah