Tech Tip: Convertible Mustang Vibration - Got MIG?

Tech Tip: Convertible Mustang Vibration – Got MIG?

Customers may come to you after many frustrating attempts by other shops to get an irritating vibration out of their 1996-98 Ford Mustang convertibles equipped with a 3.8-Liter engine. The vibration or shake seems to occur while driving at a steady speed of approximately 62 mph (100 km/h) on smooth roads. This problem may be due to the interaction between the body and the suspension.

I’ll tell you guys up front – according to the factory, you’ll need a certified welding tech with a MIG welder to accomplish step 11 of this procedure. The bulk of the repairs, though, can be easily accomplished in the shop with satisfactory results.

Customers may come to you after many frustrating attempts by other shops to get an irritating vibration out of their 1996-98 Ford Mustang convertibles equipped with a 3.8-Liter engine. The vibration or shake seems to occur while driving at a steady speed of approximately 62 mph (100 km/h) on smooth roads. This problem may be due to the interaction between the body and the suspension.

To address this problem, you should first perform steps 1-7 of the "Service Procedure" to insure the vibration is not due to any common cause condition. If vibration is still unacceptable, install the parts listed in this article to reduce the vehicle’s sensitivity to vibration.

Service Procedure
1. Verify the tires are not flat spotted, out of round, or excessively worn and the rims are not damaged.

2. Set all tire pressures to the pressure recommended on the vehicle label.

3. If this vehicle is a 1998 model with 16" tires and an automatic transmission, set the tire pressure to 30 psi (207 kPa).

4. Verify that the lateral and radial run-out of the wheel is less than 0.045" (1.14 mm), then check to make sure the tires are properly balanced on a calibrated tire balancer.

5. Normalize engine and transmission mounts to eliminate possible stressed or bound up conditions (loosen the mounts, start engine to settle components and then retighten the mounts).

6. Check for loose suspension fasteners, control arms, steering rack or cross-member.

7. Replace any worn suspension or steering components.

8. Re-evaluate the vehicle. If OK, return to the customer.

NOTE: Some Mustang convertibles may be more sensitive to vibration than others. If unacceptable vibration is still detectable, perform steps 9 through 13.

9. Disconnect the negative battery cable.

10. Replace the engine mounts with a new set of stiffer engine mounts.

11. Install a set of underbody rails. Refer to Figure 1 to determine where to place the rails to the underbody. The underbody rails will need to be welded to the underbody of the vehicle.

Special Notes
• A MIG welder and a standard body "gas metal arc welding" repair procedure should be used.
• Remove the paint in the welding area, underbody and rails, for better weld penetration.
• The welds should have a minimum 0.25" (5 mm) weld bead and a minimum total length of 3" (75 mm) on both sides of the rail (Figure 2).
• Upon completion, the welded area should be treated for corrosion using a Super Seal Anti-Corrosion Compound.

NOTE: If this vehicle has an automatic transmission, transfer the attaching shift cable retainer from the body to the bracket that is located on the underbody rails. This is important to ensure the shifter cable does not hang down.

12. Reconnect the battery.

Ford Parts Information
• XR3Z-76101W09-AA – Underbody Rail – Left.
• XR3Z-76101W08-AA – Underbody Rail – Right.
• XR3Z-6038-DA – Engine Mount – Right.
• XR3Z-6038-DB – Engine Mount – Left.
• F3AZ-19515-SA – Super Seal Anti-Corrosion Compound.

Repair Times
• Check tire condition/pressure/balance, normalize mounts, inspectfor loose fasteners and road test: 1.3 (approx. hours).
• Replace engine mounts and install/weld underbody rails: 2.0 (approx. hours).

Although this procedure appears to be drastic, the vibration can be very annoying. I know many customers that would sell their Mustangs because of the vibration, or sell their souls to get rid of it. Besides the other areas of expertise your shop is famous for, this repair could easily establish you as the premiere Mustang convertible "Vibration Eradication Specialists." And who wouldn’t want that reputation?

Written by ALLDATA Technical Editor, Rich Diegle. Rich is an Advanced Engine Performance Certified and ASE Master Technician with an Associate of Arts degree in automotive technology and 22 years of dealership and independent shop experience.

Courtesy of ALLDATA.

For additional information, visit www.alldata.com.

You May Also Like

CITGO Enters EV Space with Pilot Program Launch

The CITGO location on 11 Mile Road in Michigan now offers both regular transportation fuel and EV charging stations.

CITGO Petroleum Corporation, along with marketer Folk Oil Company, recently launched an electric vehicle (EV) charging pilot program they said is designed to meet the needs of EV drivers in Battle Creek, Mich. The CITGO location at 15551 11 Mile Road now offers both regular transportation fuel and EV charging stations. For added consumer convenience, EV chargers include both Charging System (CCS) and the North American Charging Standard (NACS) plugs, the companies said.

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion
Stellantis Increasing Production of Electric Drive Modules

The company will add EDM production in Szentgotthard, Hungary, targeted to begin in late 2026.

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Tool Time Podcast: Clore Automotive

Jim O’Hara from Clore Automotive joins Nadine Battah and Eric Garbe.

Other Posts

TechShop, ShopOwner Offer $50 For Good Guesses

Guess the Tool for a chance at cold hard cash!

GM, Honda Begin Volume Production of Fuel Cell Systems

GM and Honda will produce fuel cells that will be two-thirds less expensive compared to Honda’s 2019 Clarity fuel cell.

Toyota Bringing Battery EV Production to Kentucky

It will invest $1.3 billion at its flagship Kentucky facility for future electrification efforts, including assembly of an all-new, three-row battery electric SUV for the U.S. market.

Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.