Tech Tip: Coolant Leak from Intake Manifold Water Outlet on Nissan Frontier and Xterra Models

Tech Tip: Coolant Leak from Intake Manifold Water Outlet on Nissan Frontier and Xterra Models

Vehicle owners may complain of engine coolant under the vehicle when parked or the smell of coolant when the engine is warm. The cause may be coolant leaking between the water outlet housing and intake manifold sealing surfaces.

Applicable vehicles: all 2000-’02 Frontier (D22) with a VG33E engine; and all 2000-’02 Xterra (WD22) with a VG33E engine.

An applied vehicle may exhibit:
• Engine coolant under the vehicle when parked; or

• Smell of coolant when the engine is warm.

The cause may be coolant leaking between the water outlet housing and intake manifold sealing surfaces (see Fig. 1). Refer to the Service Procedure to ­resolve this incident if it occurs.Figure 1

Note: A leak from the above-noted area can be verified by a visual inspection.

Service Procedure:
Install the new fiber gasket between the water outlet housing and intake manifold as follows:

Caution: Be careful not to spill engine coolant on electrical connectors, drive belts, etc. when performing the following procedure.

1. Verify the coolant leak is coming from the water outlet housing/intake manifold sealing surfaces.

2. Use the valve on the lower radiator tank to drain the coolant into a clean bucket (or other clean, suitable container), to just below the level of the water outlet housing.
Note: Draining the coolant below the level of the water outlet housing will minimize coolant spillage when removing the housing.

3. Remove the parts necessary to access the water outlet housing.

4. Remove the water outlet housing from the intake manifold.

5. Thoroughly clean the sealing surfaces of the water outlet housing and intake manifold, making sure all old sealer is completely removed.

6. Install the new fiber gasket onto the water outlet housing as follows:

a. Install the two mounting bolts through the holes in the water outlet housing.

b. Slide the fiber gasket over the bolts until it is flush against the sealing surface of the housing. The bolts will keep the gasket in place while installing the housing.

7. Install the water outlet housing to the intake manifold and tighten the bolts to 16.3-20.3 Nm (12-15 ft.-lbs.).

8. Reinstall all components that were previously ­removed.

9. Refill the radiator with the coolant that was drained and captured in step 2, and according to the Coolant Refilling Procedure outlined in the “MA” section of the applicable service manual, to ensure air bubbles are purged from the cooling system.

Note: If additional coolant is needed, use a 50/50 mixture of Genuine Nissan Antifreeze Coolant (or equivalent) and distilled water or demineralized water.

10. Run the engine and confirm there is no coolant leak(s).

Courtesy of Mitchell 1.

You May Also Like

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Technology is defined as the application of scientific knowledge for practical purposes, especially in industry. We often picture technology as something that has computers and electronics attached, and often it does. But, in the world of impacts, both in the realm of pneumatic and cordless, technology bears much deeper roots.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter
More Than A Scan Tool

Scan tools serve as indispensable diagnostic hubs, offering access to a wealth of resources, from OEM technical bulletins to community-documented repairs.

scan tool
Battling Stress and Burnout

Here are some quick tips for managing stress and avoiding burnout in the fast-paced automotive repair industry.

Nadine Battah