Tech Tip: Curing Rough Idle and Hesitation on Mazda 626 Models

Tech Tip: Curing Rough Idle and Hesitation on Mazda 626 Models

Some 2000-2002 Mazda 626 models with the FS 4-cylinder engine may experience a rough idle, hesitation, stumble and/or misfire during or immediately after a cold start. A DTC P0303 may also be stored in memory. In extreme cases, the engine may stop running and multiple misfire codes, like P0300-P0304, may be stored in memory.

Some 2000-2002 Mazda 626 models with the FS 4-cylinder engine may experience a rough idle, hesitation, stumble and/or misfire during or immediately after a cold start. A DTC P0303 may also be stored in memory. In extreme cases, the engine may stop running and multiple misfire codes, like P0300-P0304, may be stored in memory.

Automotive fuel with high alcohol content may damage the fuel pressure regulator diaphragm. The damage to the diaphragm may allow fuel to enter the vacuum supply line for the fuel pressure regulator. The vacuum supply line uses the No. 3 intake runner as the vacuum source. The unmetered fuel entering the No. 3 cylinder on cold starts may cause a rich mixture misfire.

The diaphragm material has been modified, and a new fuel pressure regulator has been established as a service part (P/N FSY1-13-280). Customers with this concern should have their vehicle repaired using the following procedure.

Repair Procedure:
1. Verify the concern by inspecting the fuel pressure regulator vacuum supply hose for evidence of fuel entering the vacuum supply line.

  • If no evidence of fuel or fuel smell is found, refer to the repair manual (section 01) for further diagnostics.
  • If evidence of fuel or fuel smell is found, proceed to next step.

2. Replace the fuel pressure regulator with a new part according to the repair manual (section 01-14 Pressure Regulator or Removal/Installation).

3. Verify the repair by allowing the vehicle to fully warm up, then allow at least a six-hour cooldown (overnight, if possible) before restarting the engine.

For additional information, visit www.mitchell1.com.

Technical service bulletin courtesy of Mitchell 1.

You May Also Like

Mullen Road Tests Solid-State Polymer Battery Pack

The results met or exceeded all requirements targeted for the first drive cycles for energy usage and driving range.

Mullen Automotive began Class 1 EV cargo van road testing with an integrated solid-state polymer battery pack. Vehicle road testing began on Feb. 26 at Mullen’s Commercial Tech Center in Troy, MI.

Mullen’s latest phase of solid-state polymer battery testing began in January with the installation of the battery pack into the Class 1 EV cargo van for testing system compatibility between the vehicle and pack. Recent performance testing has included on-road drive cycles as well as Dyno testing at an EPA-certified lab located in Northville, MI, Mullen said.

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

TurnOnGreen, Endliss Power Team up to Expand EV Charging

TurnOnGreen said it will leverage EPI’s expertise in administering and executing power purchase agreements with commercial clients.

Autel’s ADAS Bay Max Vehicle Lift

Learn how this lift integrates mechanical repair, four-wheel alignment, and ADAS calibration, prioritizing efficiency and space utilization in your shop.

Switch EV Trainer Provides Tailored EV Tech Training

The Switch EV Trainer includes all of the components of a modern EV drivetrain on a compact, insulated, mobile platform.

Other Posts

Tool Time Podcast: SATA USA

In this all new episode of the Tool Time Podcast, Nadine and Eric sit down with Chris Springer of SATA USA.

Elywhere Launches in North America

Elywhere chargers can be configured to support power in the 1 MW range, providing solutions for electric fleets.

#3 Screwdriver “Tips”

What appears as one of the most basic tools in your box is far from it.

#2 Calipers & Micrometers

Calipers and Micrometers are essential measuring tools when exact precision is required.