Tech Tip: Curing Steering Wheel Vibration Felt During Braking

Tech Tip: Curing Steering Wheel Vibration Felt During Braking

Customers may report that a vibration or "judder" is felt in the steering wheel during braking. The front brake discs may have worn unevenly, resulting in thickness variations on the disc. The remedy is to install two new front brake discs (Land Rover P/N SDB000201) in combination with new specification front brake pads (Land Rover P/N SFC500050).

Karl enjoys watching classic movies, especially ones involving exploration and adventure. Many of his favorites feature a Land Rover. He can see himself commanding a safari expedition, perched atop his Rover, on the lookout for big game. Unfortunately, the reality of carting kids to baseball and soccer practice leaves little time for African safaris.

One adventure he enjoys in his 2003 Range Rover is weekend camping with his family. Upon returning from his most recent camping excursion, Karl called about a problem with the car. He said that the Range Rover had developed a vibration in the steering wheel, but only when he stepped on the brake pedal. I did some research and found a solution to his problem.

Customers may report that a vibration or “judder” is felt in the steering wheel during braking. The front brake discs may have worn unevenly, resulting in thickness variations on the disc. The remedy is to install two new front brake discs (Land Rover P/N SDB000201) in combination with new specification front brake pads (Land Rover P/N SFC500050).

APPLICABLE VEHICLES
New Range Rover (LM) up to 4A 159171.

REPAIR PROCEDURE
(Review Brake Pad and Rotor replacement along with safety procedures.)

1. Remove the front brake pads.

2. Remove and replace each front rotor as follows:
– Remove the two bolts securing the left-hand brake caliper to the hub.
CAUTION: The caliper MUST NEVER hang on the brake hose during the repair.
– Release the caliper from the hub and tie aside avoiding strain on the brake hose.
– Remove the Allen screw securing the brake disc to the drive flange and remove the disc. (Figure 1).
– Ensure the mating surfaces of the new disc and of the drive flange are clean.
– Install a new disc (SDB000201) to the flange. Install Allen screw and tighten to 16 Nm (12 lbf.ft).
– Position the caliper to the hub, install bolts and tighten to 110 Nm (81 lbf.ft).

3. Perform step 2 on the alternate side brake disc.

4. Install the new front brake pads (SFC500050).

Written by ALLDATA Technical Editor, Eric Seifert. Eric is an ASE certified Master Technician and Engine Machinist. He is a graduate of the De Anza College Automotive Technology Program, with 20 years of independent shop and parts store experience.

For information on products offered by ALLDATA, visit www.alldata.com.

You May Also Like

Mullen Road Tests Solid-State Polymer Battery Pack

The results met or exceeded all requirements targeted for the first drive cycles for energy usage and driving range.

Mullen Automotive began Class 1 EV cargo van road testing with an integrated solid-state polymer battery pack. Vehicle road testing began on Feb. 26 at Mullen’s Commercial Tech Center in Troy, MI.

Mullen’s latest phase of solid-state polymer battery testing began in January with the installation of the battery pack into the Class 1 EV cargo van for testing system compatibility between the vehicle and pack. Recent performance testing has included on-road drive cycles as well as Dyno testing at an EPA-certified lab located in Northville, MI, Mullen said.

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

TurnOnGreen, Endliss Power Team up to Expand EV Charging

TurnOnGreen said it will leverage EPI’s expertise in administering and executing power purchase agreements with commercial clients.

Autel’s ADAS Bay Max Vehicle Lift

Learn how this lift integrates mechanical repair, four-wheel alignment, and ADAS calibration, prioritizing efficiency and space utilization in your shop.

Switch EV Trainer Provides Tailored EV Tech Training

The Switch EV Trainer includes all of the components of a modern EV drivetrain on a compact, insulated, mobile platform.

Other Posts

Tool Time Podcast: SATA USA

In this all new episode of the Tool Time Podcast, Nadine and Eric sit down with Chris Springer of SATA USA.

Elywhere Launches in North America

Elywhere chargers can be configured to support power in the 1 MW range, providing solutions for electric fleets.

#3 Screwdriver “Tips”

What appears as one of the most basic tools in your box is far from it.

#2 Calipers & Micrometers

Calipers and Micrometers are essential measuring tools when exact precision is required.