Tech Tip: GM Power Steering Gear Pop or Crunch Noise

Tech Tip: GM Power Steering Gear Pop or Crunch Noise

Some GM vehicle owners may experience a crunch and/or popping sound during low-speed turning. This condition is caused because the lower control arm may be striking the steering knuckle during full-turn type maneuvers, causing the crunch sound. Slight movement between the steering gear attaching bolt threads and the frame rail inboard steering gear attaching holes may cause the popping sound.

Application
GM power steering gears: 27-6535, 6560, 7525, 7547, 7549, 7561, 7562,7563, 7573 and 7583.

Problem
Crunch and/or popping sound during low-speed turning.

Cause
The lower control arm may be striking the steering knuckle during full-turn type maneuvers, causing the crunch sound. Slight movement between the steering gear attaching bolt threads and the frame rail inboard steering gear attaching holes may cause the popping sound.

Solution
Crunch Sound: Applying a light coat of grease on the control arm and knuckle where contact is made should reduce the noise.

Popping Sound: Examine the frame rail inboard steering gear attaching holes for evidence of bolt thread contact. Enlarge inboard mounting holes that show contact only enough to allow the bolt threads to be free in the frame holes (use appropriate tools for the job). Reinstall the gear, but do not tighten bolts 1, 2 and 3 (see figure 1). Then perform the following steps:

1. Start the vehicle and cycle the steering lock to lock several times, allowing the gear to reposition itself.

2. Torque attaching bolts (1, 2 and 3) to 70 ft. lbs. (95 Nm).

Please refer to the vehicle service manual for detailed gear removal and installation procedures.

Note: This Pro Tech bulletin is supplied as technical information only and is not an authorization for repair.

Tech Tip courtesy of CARDONE.

For additional information on products offered by CARDONE, visit www.cardone.com.

You May Also Like

Mullen Road Tests Solid-State Polymer Battery Pack

The results met or exceeded all requirements targeted for the first drive cycles for energy usage and driving range.

Mullen Automotive began Class 1 EV cargo van road testing with an integrated solid-state polymer battery pack. Vehicle road testing began on Feb. 26 at Mullen’s Commercial Tech Center in Troy, MI.

Mullen’s latest phase of solid-state polymer battery testing began in January with the installation of the battery pack into the Class 1 EV cargo van for testing system compatibility between the vehicle and pack. Recent performance testing has included on-road drive cycles as well as Dyno testing at an EPA-certified lab located in Northville, MI, Mullen said.

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

TurnOnGreen, Endliss Power Team up to Expand EV Charging

TurnOnGreen said it will leverage EPI’s expertise in administering and executing power purchase agreements with commercial clients.

Autel’s ADAS Bay Max Vehicle Lift

Learn how this lift integrates mechanical repair, four-wheel alignment, and ADAS calibration, prioritizing efficiency and space utilization in your shop.

Switch EV Trainer Provides Tailored EV Tech Training

The Switch EV Trainer includes all of the components of a modern EV drivetrain on a compact, insulated, mobile platform.

Other Posts

Tool Time Podcast: SATA USA

In this all new episode of the Tool Time Podcast, Nadine and Eric sit down with Chris Springer of SATA USA.

Elywhere Launches in North America

Elywhere chargers can be configured to support power in the 1 MW range, providing solutions for electric fleets.

#3 Screwdriver “Tips”

What appears as one of the most basic tools in your box is far from it.

#2 Calipers & Micrometers

Calipers and Micrometers are essential measuring tools when exact precision is required.