Tech Tip: Installing Timing Belt Covers with Guides for 2001 Hyundai Sonata, Santa Fe

Tech Tip: Installing Timing Belt Covers with Guides for 2001 Hyundai Sonata, Santa Fe

Some 2001 Hyundai Sonata and Santa Fe vehicles may experience rough running, rough idle, lack of power at low rpm, or the check engine light on. This may be caused by the exhaust camshaft coming out of time, which can be fixed by installing a new timing belt cover.

Some 2001 Hyundai Sonata and Santa Fe vehicles may experience one or more of the following conditions:

– Rough running;
– Rough idle;
– Lack of power at low rpm; or
– Check engine light on (DTC P0335 crankshaft position sensor malfunction).

This may be caused by the exhaust camshaft coming out of time. A new timing belt cover (P/N 21360-38214-D) that incorporates a timing belt guide has been installed on vehicles produced since Jan. 30, 2001 (see Fig. 1).

Vehicles that experience the condition described above should be updated with the new timing belt cover following the steps in this Tech Tip. figure 1

Applicable Models: 2001 Hyundai Sonata and Santa Fe with 2.4L engine

Inspection:

1. Inspect the production date of the vehicle. Vehicles produced on or after Jan. 30, 2001, are not affected by this Tech Tip.

2. Remove the upper timing belt cover.

3. Rotate the crankshaft until the timing mark of the intake cam sprocket is aligned with the timing mark on the rocker cover.

4. Inspect the alignment of the timing mark on the exhaust cam sprocket with the timing mark on the rocker cover:
 a. If the exhaust timing mark is properly timed, skip to step 13.
 b. If the exhaust timing mark is not timed properly, continue to the Repair Procedure.

Repair Procedure:

1. Remove the right front wheel and engine splash shields.

2. Lower the vehicle and support the engine with a floor jack.

3. Remove the right-side engine mount, water pump pulley, accessory drive belts and lower timing belt cover.

4. Set the engine to top dead center (TDC) and set the intake and exhaust cam sprockets on their timing marks (as close as possible).

5. Remove the auto tensioner and timing belt.
 a. Inspect the timing belt. If it’s worn, cracked or frayed, replace it.
 b. Inspect the tensioner. If it’s leaking fluid, replace it.

6. Slowly compress the tensioner in a vise (apply pressure until resistance is felt, allow tensioner to compress, then apply more pressure) until the locking pin can be re-installed. A locking pin is supplied with a new tensioner. If an extra locking pin is not available, a 3/64” steel pin can be substituted. figure 2

7. Install the cam sprocket holder (SPX/Kent-Moore P/N 09231-38000 or equivalent) to hold the cam sprockets in alignment during timing belt installation. Install the tool 1/4” deep after the sprocket timing marks are in alignment.

Note: Insert the tool only 1/4” to make it easier to remove after the timing belt is installed.

8. Set the oil pump sprocket so that timing marks #7 and #8 are aligned. Quickly rotate the sprocket back and forth, between the 9 and 12 o’clock positions “feeling” for a “centering feel” when the timing marks meet. If the sprocket timing mark feels like it wants to move away from the other mark, rotate the sprocket one complete revolution and try it again (see Fig. 2).

9. Verify the following timing marks are aligned (see Fig. 3):
 a. Camshaft sprockets (intake 1, 2; exhaust 3, 4). figure 3
 b. Balance shaft (5, 6) and oil pump sprocket/balance shaft (7, 8).
 c. Crankshaft (9, 10).

10. Wrap the timing belt in a clockwise direction starting from the intake cam sprocket. Keep the belt tight when installing it over the exhaust cam sprocket, oil pump sprocket/balancer and crankshaft.

11. Apply hand pressure to the tensioner pulley to take up any slack, and remove the lock pin from the tensioner. Remove the cam sprocket holder (see Fig. 4).

12. Rotate the crankshaft clockwise (by hand) two complete revolutions and set to TDC. If the TDC mark was passed, then rotate the crankshaft another two complete revolutions. The crankshaft must be turned clockwise only for proper tension and orientation of the timing marks.

13. Inspect the timing marks of the cam sprockets for proper timing. Figure 4

Note: Due to the difference in ratio between the crank sprocket and the oil pump sprocket, the oil pump sprocket will appear out of time after turning the crankshaft two revolutions (provided the sprocket was set properly in steps 8 and 9). The oil pump sprocket will come into alignment on the sixth revolution (1:1.5 ratio; crank to oil pump).

14. If the timing marks are properly timed, rotate the crankshaft an additional 90° to take the marks off of TDC.

15. Reassemble the engine (if applicable) and install a new timing belt cover P/N 21360-38214-0.

16. Test-drive the vehicle to confirm that the condition has been corrected.

 

Written by Dennis Shortino, ALLDATA editor, and Jeff Webster, ALLDATA technical writer.

You May Also Like

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion

The corporate world has offices. You hang pictures on the wall, keep a few trinkets on your desk and a few snacks in one of your desk drawers. It’s your space. As technicians, we have our toolbox. It’s our “office” on wheels. But it’s different. We have no “work from home” option. We can’t take it with us and work at a coffee shop. Our “office space” becomes far more important. This is where we make our living.The size of a toolbox and the features we choose depend on multiple factors, which have changed over the years along with automotive and tool technology. Here’s a look at some of the core features and modern frills to consider when it’s time to move into a new office.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
PRT Launches 22 New Products on Complete Strut Assemblies

The new items come to expand the PRT portfolio in North American Market and represents more than 12 Million vehicles in new coverage.