Tech Tip: Master Cylinder Inspection

Tech Tip: Master Cylinder Inspection

Although the mechanics of modern master cylinders seem deceptively simple, today's dual-piston or tandem master cylinders still require the utmost in care and attention to maintain safe, reliable operation.

By Gary Goms
Technical Contributor

Although the mechanics of modern master cylinders seem deceptively simple, today’s dual-piston or tandem master cylinders still require the utmost in care and attention to maintain safe, reliable operation. The tandem master cylinder contains two piston assemblies; one for each axle set or diagonally located pair of brakes. Each piston assembly has two lip seals mounted in grooves on the pistons. The rearmost piston cup or lip seal holds the fluid in the master cylinder and against the back of the forward cup. The forward cup applies hydraulic pressure to the braking system as the brake pedal is depressed.

A return spring, which is contained in the front of the master cylinder bore, returns the piston assembly to a rest position after the driver releases pressure on the brake pedal. As the piston returns to the rest position, brake fluid flows around the lip of the forward seal to replenish fluid in the master cylinder bore. In all drum brake, single-cylinder designs, the return spring holds a residual check valve in place to retain a few pounds per square inch of pressure in the hydraulic system.

Depending upon the application, tandem dual master cylinders may incorporate a residual check valve in one or both outlet ports located on the side of the cylinder (see Figure 1). Residual pressure prevents air from migrating into the brake hydraulics and preloads a drum brake’s wheel cylinder linkage. Because of improved design, many later-model drum applications eliminated the residual check valve altogether.

Looking into the reservoir, each of the tandem cylinders has a “breather” port that allows the piston to draw fluid into the cylinder behind the forward cup. The compensation port, which is located forward of the breather port, allows fluid pressure to bleed out of the cylinder bore when the brake pedal is released. The compensation port also allows air to bleed from the cylinder into the master cylinder reservoir as the pedal is depressed.

The most important point to remember during any master cylinder diagnosis is that an inch of travel at the brake pedal translates into only a few thousandths of an inch of piston travel at a disc brake caliper or brake cylinder. Consequently, the fluid displacement of a master cylinder is matched very closely to the fluid volume requirements of the brake system itself.

Obviously, the clearance between a brake pad and rotor may drastically affect master cylinder operation. Some caliper applications use a square-cut piston seal to retract the piston a few thousandths of an inch when the brakes are released. Some caliper applications may require a “quick-take-up” cylinder (see Figure 2) to close these relatively large pad-to-rotor clearances as the brake pedal is applied.

FAILURE PATTERNS
As the piston seals wear or the cylinder bore becomes scuffed or pitted, piston seal leaks cause a falling or spongy feel in the brake pedal. The falling pedal symptom is caused by fluid leaking from the brake hydraulic system into the atmosphere or by fluid leaking internally around the piston seals.

A spongy brake pedal can occasionally be attributed to a master cylinder with a worn rear seal. In these cases, air enters the cylinder as the pedal is released and is sometimes pumped into the hydraulic system.

A worn rear seal will also allow brake fluid to mysteriously disappear from the master cylinder reservoir into the vacuum brake booster and ultimately into the engine intake itself. One indicator of this condition, of course, is fluid consumption without evidence of external leakage. Another indicator is a wet area forming around the mounting flanges of the master cylinder.

DIAGNOSTICS
Brake pedal feel is often vehicle-specific because some vehicles allow for a longer length of brake pedal travel than others. In general, a good master cylinder should provide a positive, controlled sense of braking. A falling, spongy or low pedal, on the other hand, indicates a problem with the master cylinder or the brake system hydraulics.

A worn master cylinder might be detected by gradually applying pressure to the brake pedal with the engine running to provide assist. If the lip seals in the cylinder are excessively worn, the pedal may sink completely to the floor during a gradual application.

Occasionally, a newly installed master cylinder will fail to release pressure from the brake hydraulic system and cause the brakes to either lock up or drag. In these cases, the forward lip seal has failed to retract past the compensator port due to a faulty adjustment on the brake booster push rod, or a bad adjustment of the brake light or cruise control vacuum break switch on the brake pedal lever. A quick way to test for piston retraction is to gently probe through the compensating port with the blunt end of a paperclip (see Figure 3). If the cylinder has an open-top reservoir, depressing the brake pedal should cause fluid to spurt from a momentarily open compensator port. Some master cylinders are very aggressive in this regard.

You May Also Like

Wrenchers Doubles Repair Tool & Equipment Offering

More than 25,000 lifts, tools, and equipment from 39 brands available online or by phone.

Wrenchers has more than doubled the vehicle repair tools and shop equipment available in its new catalog, offering over 25,000 car lifts, specialty tools, tire changers, shop fans, and more from 39 brands. 

“We are committed to continuously improving our product lineup to make Wrenchers a one-stop-shop for tools and garage equipment,” says Karla Zarate, director of sales operations. “When we launched Wrenchers as an improved version of long-time distributor Garage Equipment Supply in 2022, we had about 12,000 product numbers in our catalog. We’re at more than 25,000 now, with more in the pipeline. This means our customers can get more of what they need with just a click, rather than having to waste time shopping around.”

Myers Tire Supply Introduces MTS Xpresstm

The innovative solution to consolidate purchases and control inventory costs.

Experiencing What the Tool Industry Has to Offer

ETI held its annual ToolTech conference April 17-19 at the Hyatt Regency Tamaya Resort in Santa Ana Pueblo, New Mexico.

Sandia Mountains
LIQUI MOLY Develops Liquid Thermal Manager for EV Batteries

The automotive chemical specialist is expanding its range for all-electric vehicles with Battery Coolant EV 200.

May 2023 Vehicle Care RockStar: Johnny Weber

Johnny Weber exudes confidence in his abilities to lead the band through proficiency over pageantry.

Other Posts

Variable Valve Timing Systems

Variable valve timing systems allow today’s engines to maximize performance and drivability.

Continental Tire Upgrades Test Tracks for EVs

Continental expanded its EV charging infrastructure at three company-owned test sites in Sweden, Germany and the U.S.

Streamlight Names E.A. Langenfeld & Associates 2022 Automotive Sales Rep Agency of the Year

The company received the award yet again in recognition for outstanding national sales achievement.

MAHLE and Midtronics Join Forces for Battery Service 

The goal of the cooperation: holistic battery diagnostics and maintenance from a single source in a growing future market.