Tech Tip: Motor Mounts - Supporting the Engine and Transmission

Tech Tip: Motor Mounts – Supporting the Engine and Transmission

Motor mounts are not a very glamorous product, but they do have an important function: They support the engine and transmission, and dampen noise and vibration. The mounts isolate the engine and transmission from the chassis so vibrations and noise are not transmitted to the rest of the vehicle.

Motor mounts are not a very glamorous product, but they do have an important function: They support the engine and transmission, and dampen noise and vibration. The mounts isolate the engine and transmission from the chassis so vibrations and noise are not transmitted to the rest of the vehicle. On some front-wheel drive cars, upper mounts (torque struts) also control the fore and aft movements of the engine during acceleration.

Most motor mounts are relatively simple in design and consist only of metal attachment plates and large rubber insulator blocks. But some vehicles have “hydraulic” or “hydro-mounts” with hollow chambers filled with glycol or hydraulic fluid. Hydro-mounts act like a jelly-filled donut to absorb vibrations that would otherwise be transmitted to the chassis. Hydro-mounts are often used with four-cylinder and V6 engines that don’t idle as smoothly as a V8, and in luxury vehicles where motorists expect less noise and vibration. Some hydro-mounts even have internal valving and/or a solenoid to change the dampening characteristics at different RPM to better tune out unwanted vibrations. These are called “switchable” hydraulic mounts or “electronic” mounts.

WHEN MOUNTS GO BAD
When a motor or transmission mount fails, one of several things can happen. If the rubber separates or delaminates from the steel, the mount can break. The design of the mount usually prevents the engine from falling out of the car, but it can’t keep the engine from twisting or rocking when the vehicle accelerates or is under load. This can produce thumping and rattling noises, as well as overstressing components such as radiator and heater hoses, wiring connectors and the exhaust system. In rear-wheel drive applications that have an engine-driven fan, a broken mount may allow the fan to hit the radiator or shroud. Drive belts or pulleys may also be forced to rub against other components if clearances are tight.

A broken or loose motor mount in a front-wheel drive application can be even more serious because it may allow engine movements that interfere with the throttle or shift linkage. Excessive fore and aft rocking of a transverse-mounted engine can also lead to exhaust leaks where the head pipe joins the manifold or cause the head pipe itself to fail. If the broken mount is an end mount, it may also contribute to a torque steer condition and cause accelerated wear or separation of the inner CV joints on one or both halfshafts.

The motor mounts are seldom checked unless there is an obvious problem, and they may even be overlooked if the engine or transmission is being replaced. You should remind customers to check their motor mounts if the engines seem noisier than usual or they can feel engine vibrations inside their vehicles. The condition of the mounts should also be inspected when any major engine or transmission work is done, or when replacing a clutch, halfshafts or a driveshaft.

Mounts can be visually inspected for cracked, loose or broken brackets, loose or missing bolts, collapsed rubber or fluid leaks (hydro-mounts). A pry bar can be used to check for separated or broken mounts.

Another way to check mounts is to put the transmission into drive and lightly load the engine while keeping the other foot on the brake. Excessive engine movement may indicate loose or broken mounts that need to be replaced.

Replacement mounts may or may not have the same construction as the original. Fluid-filled hydro-mounts are expensive, so a more affordable alternative may be a solid replacement mount. But a solid mount obviously can’t provide the same level of dampening as the original hydro-mount. Consequently, the vehicle owner may not be happy with the way his car feels if a less-expensive solid mount is substituted for a fluid-filled mount.

Replacing a motor mount always requires supporting the engine and/or transmission. The weight must be taken off the mount before it can be unbolted and replaced. This can be done with a floor jack from underneath, or with an engine hoist overhead. Mount access can also be a challenge on some transverse-mounted engines in front-wheel drive cars.

Other items that may be needed when replacing motor mounts include new fasteners, new mounts for a steering rack (these should also be inspected periodically or if the steering feels loose), a new mount for the center support bearing on a rear-wheel drive vehicle with a two-piece driveshaft, new upper strut mounts (if the steering feels stiff or makes noise when turning or driving over bumps), or even new body mounts if a vehicle has a subframe and the original mounts are in bad shape.

You May Also Like

Wrenchers Doubles Repair Tool & Equipment Offering

More than 25,000 lifts, tools, and equipment from 39 brands available online or by phone.

Wrenchers has more than doubled the vehicle repair tools and shop equipment available in its new catalog, offering over 25,000 car lifts, specialty tools, tire changers, shop fans, and more from 39 brands. 

“We are committed to continuously improving our product lineup to make Wrenchers a one-stop-shop for tools and garage equipment,” says Karla Zarate, director of sales operations. “When we launched Wrenchers as an improved version of long-time distributor Garage Equipment Supply in 2022, we had about 12,000 product numbers in our catalog. We’re at more than 25,000 now, with more in the pipeline. This means our customers can get more of what they need with just a click, rather than having to waste time shopping around.”

Myers Tire Supply Introduces MTS Xpresstm

The innovative solution to consolidate purchases and control inventory costs.

Experiencing What the Tool Industry Has to Offer

ETI held its annual ToolTech conference April 17-19 at the Hyatt Regency Tamaya Resort in Santa Ana Pueblo, New Mexico.

Sandia Mountains
LIQUI MOLY Develops Liquid Thermal Manager for EV Batteries

The automotive chemical specialist is expanding its range for all-electric vehicles with Battery Coolant EV 200.

May 2023 Vehicle Care RockStar: Johnny Weber

Johnny Weber exudes confidence in his abilities to lead the band through proficiency over pageantry.

Other Posts

Variable Valve Timing Systems

Variable valve timing systems allow today’s engines to maximize performance and drivability.

Continental Tire Upgrades Test Tracks for EVs

Continental expanded its EV charging infrastructure at three company-owned test sites in Sweden, Germany and the U.S.

Streamlight Names E.A. Langenfeld & Associates 2022 Automotive Sales Rep Agency of the Year

The company received the award yet again in recognition for outstanding national sales achievement.

MAHLE and Midtronics Join Forces for Battery Service 

The goal of the cooperation: holistic battery diagnostics and maintenance from a single source in a growing future market.