Tech Tip: Toyota Matrix MIL ON/DTC's P0011, P0012 or P0016 Set

Tech Tip: Toyota Matrix MIL ON/DTC’s P0011, P0012 or P0016 Set

Under certain conditions, customers may experience an MIL On condition with DTC P0011, P0012 or P0016 stored in the Engine Control Module/ECM.

Models Affected: 2005-’07 Corolla and Matrix

In some cases, the cause of this DTC may be the VVT-i actuator. Use the procedures in this bulletin to verify the operation of the actuator and correct the condition.

Repair Procedure:

1. Referring to the screen flow in Fig. 1, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank 1 Active Test (VVT CTRL B1) from the Active Test Menu. fig. 1

2. Using the right arrow key, toggle the VVT actuator “ON.”

3. Does the engine run rough and/or stall?
YES: Proceed to step 4.
NO: Check the oil control valve operation.

Refer to the Technical Information System (TIS):
– 2005 Corolla or Matrix Repair Manual, ­Engine/Hybrid System – Engine Control – “1ZZ-FE/2ZZ-GE: SFI System: Inspection”
– 2006-’07 Corolla or Matrix Repair Manual, ­Engine/Hybrid System – Engine Control – “1ZZ-FE/2ZZ-GE: Engine Control System: Camshaft Timing Oil Control Valve Assembly: Inspection”

4. Remove and replace the camshaft timing gear ­assembly. Refer to TIS:
– 2005 Corolla or Matrix Repair Manual, ­Engine/Hybrid System – Engine Mechanical – “1ZZ-FE/2ZZ-GE: Camshaft: Replacement”
– 2006-’07 Corolla or Matrix Repair Manual, ­Engine/Hybrid System – Engine Mechanical – “1ZZ-FE/2ZZ-GE: Engine Mechanical: Camshaft: ­Removal” fig. 2

Note: The timing gear must be in the unlocked ­position when installing it on the camshaft.

See step 5 for instructions to unlock the camshaft timing gear.

5. Identify whether the camshaft timing gear is ­unlocked or locked. See Fig. 2.
– If the camshaft timing gear is unlocked, it’s ready to install.
– If it’s locked, follow the steps below to unlock the camshaft timing gear before installing.

a. To disengage the camshaft timing gear lock pin, apply and hold approximately 21 psi of air pressure at the oil feed hole located 90° clockwise of the oval slot. See Fig. 3.
fig. 3
Note: The lock pin is inside the gear, not the one ­located in the oval slot.

b. With the 21 psi of air still applied to the gear, turn the interior assembly counterclockwise. (See blue arrow in Fig. 3.)
c. Install the timing gear assembly onto the camshaft with the straight pin slightly to the right of the key groove as shown in Fig. 4.
d. Turn the camshaft timing gear assembly while pushing it lightly against the camshaft until the straight pin engages the key slot.
e. Check that the camshaft timing gear is fully seated on the camshaft and that there is no clearance ­between the end of the camshaft and the timing gear. Install the camshaft bolt finger tight. See Fig. 4a.
f. While holding the camshaft with a wrench, tighten the camshaft bolt. Torque: 54 Nm (40 ft.-lbf.)
g. After torquing the camshaft bolt, rotate the camshaft timing gear in a clockwise direction while holding the camshaft stationary until the dots are aligned, thereby engaging the camshaft timing gear lock pin. See Fig. 5.
h. The timing gear is now ready for installation of the timing chain.

Note: Camshaft timing is performed with the camshaft timing gear in the locked position (dots aligned).

fig. 4

 fig. 4a

 Fig. 5

Courtesy of Mitchell 1.

You May Also Like

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Technology is defined as the application of scientific knowledge for practical purposes, especially in industry. We often picture technology as something that has computers and electronics attached, and often it does. But, in the world of impacts, both in the realm of pneumatic and cordless, technology bears much deeper roots.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Upgrade Your Air System: It’s Easier Than You Think

Improving your shop airflow is only a benefit, unless you like to spend more time, work harder and make less money.

air flow tubes
Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter
More Than A Scan Tool

Scan tools serve as indispensable diagnostic hubs, offering access to a wealth of resources, from OEM technical bulletins to community-documented repairs.

scan tool