Tech Tip: Understanding Electrical Basics Can Save Technicians Time and Money

Tech Tip: Understanding Electrical Basics Can Save Technicians Time and Money

Sophisticated automotive electrical systems can cause increasing amounts of dead batteries, intermittent warning lights and general electrical complaints. When addressing these issues, staying focused on the basics can save you time, money and nerves.

by The WORLDPAC Training Institute (WTI) Team

Sophisticated automotive electrical systems can cause increasing amounts of dead batteries, intermittent warning lights and general electrical complaints. When addressing these issues, staying focused on the basics can save you time, money and nerves.

Automotive electrical basics are:
• Connection condition;
• Battery condition; and
• Alternator condition.

Connection Condition
In order of importance, connection condition (at least to the battery) really does come first. Without a good solid connection to the battery, the vehicle may not start, charge, or it could generate a few unwanted electrical gremlins. Clean tight connections from the battery to the chassis grounds and to the alternator and starter motor will eliminate subtle electrical gremlins. The condition of all electrical connections and the circuits they connect to can be easily tested using the voltage drop test. You will find bad relays, bad fuses, poor connections and faulty ignition switches within minutes (opposed to hour or days.) This may be the single most important test for technicians to implement into diagnostic routing when searching for a cause to an intermittent electrical complaint.

Battery Condition
Battery condition is paramount on today’s vehicles because the on-board computers will be the first to react to a problem within the battery. Computers are reliant on continuous, uninterrupted current flow between the positive and negative terminals of the battery. One bad plate in the battery can cause a multitude of electrical problems after you start the engine. You may be thinking, “That’s odd, I thought if the battery was bad the starter motor wouldn’t crank the engine?” Not true. As a technician on today’s vehicles, you need to toss out this old thought process. Before addressing electrical complaints on late-model vehicles, check the condition of the battery to ensure it is not the cause of the current fault.

Alternator Condition
After a battery has been determined to be in good condition, you will need to determine the condition of the alternator. With the numerous electronics operating late-model vehicles, the alternator output on some cars may exceed 200 amps! With that much output, the main power lead to the alternator may be fuse protected. Before replacing an alternator because of “no output,” double check the manufacturer’s information regarding their test procedures. You may discover that a fuse, fusible link or specially designed cable is the cause of the no output problem. One other note, be advised that some late-model vehicles could have alternators that are networked and diagnosing them will be different.

Tech Tip courtesy of WORLDPAC Training Institute (WTI).

For additional information on WORLDPAC Training Institute (WTI) and products offered by WORLDPAC, visit www.worldpac.com.

You May Also Like

Clarios Formalizes Joint Development Agreement with Altris

Altris will develop sodium ion cells for low-voltage tech while Clarios will lead in battery management systems, software, and system integration for battery design.

Clarios and Altris, a Swedish developer and prototype manufacturer of sodium-ion batteries, announced an exclusive Joint Development Agreement (JDA) for low-voltage mobility applications.

Under the new JDA, Altris will focus on developing the sodium ion cell technology for low-voltage applications, while Clarios will leverage its expertise in Battery Management Systems (BMS), software, and system integration to design the battery system. This development agreement enhances a collaboration agreement initiated earlier this year, which set in motion the creation of a detailed production plan for low-voltage vehicle batteries utilizing sodium-ion cells, the companies said.

Less is More with Cordless Work Lights

The automotive industry has reaped the benefits of LED lights more than any other industry.

Streamlight Wedge XT
Eaton to Supply ELocker Differential System to EV Manufacturer

The system leverages an electric motor to power the rear wheels and an electric motor or an optional ICE driving the front wheels.

Servicing EVs in Your Shop

Technicians need to learn how to correctly diagnose and repair electrical systems.

technician using laptop
Tool Time Podcast: Schrader TPMS

In this episode, Nadine and Eric sit down with Yanick Leduc to discuss all the TPMS solutions his company has to offer.

Other Posts

Eli Opens Reservations for its Micro-EV in the US

The new Eli ZERO represents a new category of high-tech, efficient and sustainable micro-EVs, according to Eli Electric Vehicles.

Hunter Engineering Releases New Alignment Coverage

Semi-annual specification update includes new and existing records.

#11 LED Work Lights

Light emitting diodes (LEDs) were a revolutionary development of electrical science.

LED Work Lights Feature
Eaton Receives 2024 Automotive News PACEpilot Award

Eaton was recognized for its 4-speed electrified vehicle transmission.