Tech Tip: Use Caution when Replacing Ford Diesel Cylinder Heads

Tech Tip: Use Caution when Replacing Ford Diesel Cylinder Heads

According to Ford's TSB 06-24-4, some 2003-'07 vehicles equipped with a 6.0L engine may require the cylinder head to be replaced, while design changes can affect interchangeability between model years and service of 2003-'07 6.0L engines.

Ford Motor Company has released information on a cylinder head gasket caution for 2003-’07 Ford 6.0L VIN P diesel engines.

According to Ford’s TSB 06-24-4, some 2003-’07 vehicles equipped with a 6.0L engine may require the cylinder head to be replaced, while design changes can affect interchangeability between model years and service of 2003-’07 6.0L engines.

According to the bulletin, the manufacturer for this engine used two separate facilities. And, while both locations built engines with the same design data, three cylinder head variations have been used. There are engine serial number change dates to help in determining which cylinder heads were used.

The cylinder head gasket and locating dowels also changed in the 2006 model year to accommodate the increase in the dowel size from 18 mm to 20 mm. Using the wrong head gasket for the application will lead to engine damage.

The revised dowel hole was made to accommodate the larger head bolts to be used in the new 6.4L diesel engine and was commonized for manufacturing purposes. The injector clamp design and associated cylinder head casting support area also were modified on the changeover date in early 2006.

The cylinder head and block dowel hole sizes must be measured to determine the correct cylinder head gasket kit to be used. If there is a difference in dowel hole size between the head and block, a special “stepped dowel” (P/N 6C3Z-6B041-B) is available to accommodate proper assembly.

Ford notes that the cylinder head gasket and injector clamp versions are not interchangeable; they must be used with the corresponding cylinder head versions. Refer to the chart to determine the correct application.

Courtesy of Ford Motor Co. and Ford Truck Enthusiasts (www.ford-trucks.com)

You May Also Like

Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Technology is defined as the application of scientific knowledge for practical purposes, especially in industry. We often picture technology as something that has computers and electronics attached, and often it does. But, in the world of impacts, both in the realm of pneumatic and cordless, technology bears much deeper roots.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter
More Than A Scan Tool

Scan tools serve as indispensable diagnostic hubs, offering access to a wealth of resources, from OEM technical bulletins to community-documented repairs.

scan tool
Battling Stress and Burnout

Here are some quick tips for managing stress and avoiding burnout in the fast-paced automotive repair industry.

Nadine Battah