Tech Tip: VW/Audi Throttle Body Alignment

Tech Tip: VW/Audi Throttle Body Alignment

Have you had a customer pull into the shop with a Volkswagen or Audi that just will not idle correctly? One of the possible causes is that the throttle position is not known. The ECU must know the full range of motion of the throttle in order for it to properly control the engine.

Since 1996, most gasoline-engine VAG cars have electrically controlled throttles.

Have you had a customer pull into the shop with a Volkswagen or Audi that just will not idle correctly? One of the possible causes is that the throttle position is not known. The ECU must know the full range of motion of the throttle in order for it to properly control the engine.

When the motion range is not known, the ECU simply has no idea where to set the throttle. Using the throttle position sensors in the throttle body, the ECU learns the full open and full closed positions through a process known as a Throttle Body Alignment (TBA).

A TBA needs to be performed whenever one of the ­following occur:
• Loss of voltage to the vehicle (battery disconnected or battery run down to low voltage);
• ECU has been disconnected, reconnected or ­replaced;figure 1
• Throttle body has been cleaned, removed or
­re-installed; or
• Accelerator pedal has been removed or
re-installed.

There are certain operating conditions that must be met before the throttle is adapted. These include:
• No DTCs in the engine controller;
• Battery voltage is at least 11.5V;
• The throttle should be at the idling position (keep your foot off the accelerator pedal);
• The throttle body must not be dirty (carbonized); and
• The coolant temperature must be between 5° C and 95° C.
In the example shown here, the VCDS factory-level tool is used to perform the procedure. See Fig. 1

Note: Other factory-level tools may require slightly different procedures, but should be very similar.
This procedure is performed with the key on, engine off and without touching the accelerator pedal.
Procedure for performing the TBA on DBW cars that use KWP-2000 (typical of engine controllers in 2002+ Audi A4, VW Passat and Touareg):
[Select]Figure 2
[01– Engine]
[Basic Settings—04]: Group 060
[Go!] “Basic Settings: OFF” will appear under the VCDS logo. See Fig. 2.
[ON/OFF/Next] will switch “Basic Settings: ON” under the VCDS logo. The display will show ADP RUN and the throttle will begin to cycle. Leave the tool in basic settings for 30 seconds after the display shows ADP OK.
Then click: [Done, Go Back]

Courtesy of Ross-Tech.

You May Also Like

Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool

If there’s a truth that extends across all computerized devices, it’s that we likely utilize only a fraction of the things they have the ability to do. Mobile phones are a great example. How many people do you know who only use them for calls, voicemail and text messages? We all know they do so much more.The scan tools we use every day fall into the same category. Are you maximizing yours to their full potential? Don’t let them be just an expensive code reader. That may be easier said than done, because it takes a lot of time to understand both the scan tool and how well it interacts with the vehicles you’re working on, but there are a few factors that can help you dive a little deeper into the functions at your fingertips.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Lisle Low Profile Fuel Line Disconnect – Dent Fix Soft-Shock Mallet DF-SM76 Reduces Damage – New ProMAXX Diesel Fuel Injector Seal Puller/Saver ProKits   OTC Genisys Touch – Quick scan, bidirectional control Snap-on VANTAGE Pro

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

2024 Is Your Year to Be the Technician You Always Wanted to Be

As we enter 2024, strategic career planning is essential for success in the automotive repair industry.

happy new year 2024
Software Focus: Efficient Diagnostics

Discover how to quickly retrieve codes, access exclusive repair information, and develop a strategic plan for optimal diagnostic results. This video is sponsored by Bosch.

Why ECU Reflashing Needs Certain Power Levels

A reflash power supply is not designed to jumpstart the vehicle.