Tech Update: Working on Wipers

Tech Update: Working on Wipers

It's right after a major snowstorm, and there's ice and snow on everyone's windshield. You're at the shop waiting for the phone to ring. The phone leaps off the receiver and it's Captain Chaos; he's managed to find a second use for his wiper blades. Apparently, Captain Chaos was in too much of a hurry to clean the ice off the wiper blades before turning them on. In his frantic attempt to go to work, the wiper blades have become completely useless. He can hear the wiper motor running, but the blades refuse to move.

It’s right after a major snowstorm, and there’s ice and snow on everyone’s windshield. You’re at the shop waiting for the phone to ring. The phone leaps off the receiver and it’s Captain Chaos; he’s managed to find a second use for his wiper blades. Apparently, Captain Chaos was in too much of a hurry to clean the ice off the wiper blades before turning them on. In his frantic ­attempt to go to work, the wiper blades have become completely useless. He can hear the wiper motor running, but the blades ­refuse to move.

Most likely, it’s the nut on the wiper arm that has worked loose from the wiper shaft. Since most wiper manufacturers have gone to this type of fastener, I haven’t seen as many wiper transmission failures due to snow or ice. But, there’s always our illustrious Captain who will find some way to break things.  

The next generation of “frameless” or “aero” wipers are starting to become the norm on late-model vehicles, much to the chagrin of older drivers who only want to pay for $5 ­refills for older-style blades. These blades are designed to work for late-model vehicles and often a driver will notice reduced performance and wind noise if they try to go with a cheaper frame wiper. For older cars, these wipers can be a nice upgrade.  
Diagnosing most of the mechanical parts of the wiper system is straightforward. There are exceptions to every rule, so I can’t say that every car will be easy.

Diagnosing the electric or electronic components, however, is ­another issue. We can break the systems down by years, and then determine how to diagnose the problem and make repairs. Prior to 1995, there weren’t too many complicated electrical wiper systems. To go back even farther into auto history, most wiper systems were either vacuum-operated or operated by hand. There are a few exceptions, but most of those are on ­special models. 

Although, after 1996 with the ­arrival of OBD II ­systems, a lot of the manufacturers tied their wiper systems into the ALDL connector. You can actually diagnose the wiper system with their scanner. Some even have codes that involve the wiper system, usually through the BCM unit or the CAN system.

I much prefer the newer cars for the diagnostic ­capabilities using the factory scanner to operate the front and rear wiper systems. Not to worry though, you can still diagnose the entire system with the use of an ohm/voltmeter. But, if you ever get a chance to use a factory scanner, you’ll be amazed how much simpler it is to diagnose.

One of the other things that has changed over the years is how they work, where they’ve put all the separate components and the nomenclature that each different manufacturer uses. I pulled the wiring ­diagrams on Nissan Sentra, model years 1985, 1995 and 2005. The 1985 model had a separate intermittent amp control module incorporated into the wiper system. It was mounted under the dash or near the fuse box. Its job was to control the intermittent level for the wipers.  

By the time 1995 came around, the intermittent amp control module was now called a time control module. They both did the same job; however, it was now mounted at the base of the steering column.

In 2005, things get even more compact. It’s a variable intermittent wiper control module and it’s part of the wiper switch itself. If the test results tell you to change the wiper switch, you also get lucky with the intermittent unit being changed along with it.

Before tackling any electrical system in any car, make sure you have the latest TSBs, proper wiring ­diagrams and any diagnostic information that you can get your hands on. Most good diagnostic manuals will have the impedance values and the voltage ranges in their test procedures.

Rain-sensing wipers are starting to ­become a popular option and they are even standard on some import vehicles. Some newer models have eliminated the driver-controlled intermittent setting in favor of this option.
The rain sensor projects non-visible infrared light with LEDs onto the windshield. Next to the LEDs are sensor diodes measuring how much ­infrared light is reflected back. If the glass is dry, most of this light is reflected back. If rain or snow is on the glass, the light is reflected in different directions.

Rain sensors often perform double duty as sensors for automatic headlights. If there is a problem with the sensor, chances are it could change how both the lights and wipers work.

The software sets the speed of the wipers based on how fast the moisture builds up between each wipe. But, the newer systems use vehicle speed and information from the CAN Bus for the wipe interval. This stops the wiper from flailing about at stoplights.

The rain sensor and module will also send information to the lighting module that controls the lights to turn them on if the wipers have to run for a predetermined amount of time.

One of the most common problems with these systems is not the sensor, but the windshield itself. When a windshield is replaced, it’s possible for the glass installer to mount the sensor with contaminants or adhesive in front of the sensor. Some systems will detect that the wiping action is not changing how much light is being reflected back and might not allow the driver to select the auto mode. This is where the scan tool comes in handy.
Some replacement windshields may vary enough from the OE coatings, thickness and tints to also cause the sensor to malfunction.

The condition of the wiper blades can also influence how the sensor operates. If the blades streak or leave excess water on the windshield, it will be ­detected by the sensor and the sensor will increase the number of wipes to remove the water. When testing these ­systems, use a spray bottle that leaves droplets on the windshield. Do not use a hose, as the sensor is ­designed to detect droplets, not a stream of water.

Most late-model imports use vehicle speed to ­determine the wiper interval. At lower speeds, the vehicle will increase the interval or speed. When the vehicle is put into park, the wipers may or may not enter into a hold mode.
Newer Lexus, Acura and Nissan models have controls to adjust the sensitivity of the sensor to the customer’s liking.

The adjustment method can typically be found in the owner’s manual and involves navigating through the information display. This adjustment may help some customers deal with their control issues. You can also recommend new wiper blades to improve the system’s effectiveness.

Remind your customers, especially those in the northern part of the country, to make sure they turn off their wipers before parking the car for the night, and that they clean the snow and ice off the wiper arms and blades before trying them the next morning. A ­little advice can go a long way, and, hopefully, keep Captain Chaos on the road, and out of the shop.

You May Also Like

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion

The corporate world has offices. You hang pictures on the wall, keep a few trinkets on your desk and a few snacks in one of your desk drawers. It’s your space. As technicians, we have our toolbox. It’s our “office” on wheels. But it’s different. We have no “work from home” option. We can’t take it with us and work at a coffee shop. Our “office space” becomes far more important. This is where we make our living.The size of a toolbox and the features we choose depend on multiple factors, which have changed over the years along with automotive and tool technology. Here’s a look at some of the core features and modern frills to consider when it’s time to move into a new office.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Mayhew Introduces New 14-Piece Micro Hand Tool Set – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set   OTC Genisys Touch – Quick scan, bidirectional control Snap-on

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
PRT Launches 22 New Products on Complete Strut Assemblies

The new items come to expand the PRT portfolio in North American Market and represents more than 12 Million vehicles in new coverage.