TPMS Quick Tip: TPMS Diagnostic Strategy, Check

TPMS Diagnostic Strategy, Check

If you find a tire pressure sensor isn't functioning, the natural assumption is the sensor is the problem, but is it?

Step-By-Step

One of the diagnostic mantras preached by service experts today is “test before you touch.” You should always use a TPMS tool to activate and check the response signal from each tire pressure sensor in each wheel before you do anything else. This will tell you:

            •  Whether or not each sensor is capable of generating a
    signal; and

            •  If the sensor is generating a signal, whether or not the
   pressure reading is accurate.

The pressure reading from a sensor can be easily verified by checking the actual pressure in the tire with a gauge. If the pressure value displayed on your TPMS tool reads a certain inflation pressure (psi or bar), you should find that same inflation pressure when you check with a gauge.

Your tire pressure gauge must be accurate. While spring-loaded stick-style tire pressure gauges can vary up to 5 psi or more, digital gauges are the most accurate because many have a self-calibrating feature that compensates for changes in ambient air temperature.

Bad Valves, Aging Sensors

Watch for corroded or damaged TPMS valves. The valve stem on each wheel should be visually inspected for corrosion or other damage that might affect its integrity. Certain makes and models of vehicles have gained notoriety for suffering excessive corrosion even to the point that valve-stem sensors literally fall into the tire, causing instant deflation.

Consider age and mileage when doing your diagnosis. The average life of the battery inside a new factory TPMS sensor is around seven years, depending on use. The more the vehicle is driven, the more often the TPMS sensors generate their signals, and the faster they use up their remaining battery life.

How to Proceed

If you find a tire pressure sensor that is not functioning or reading accurately, the natural assumption is that the sensor is the problem and replacing the sensor will fix the issue — and usually it will. But until you check the rest of the system, there’s no guarantee a bad sensor is the only problem affecting the operation of the TPMS.

If all of the sensors appear to be working normally and all of the tires are inflated to the recommended pressure, but the TPMS warning light remains on or flashing, you’ll have to dig deeper to uncover the fault.

For the next step, you’ll need a TPMS tool or scan tool that can communicate with a TPMS system via the OBD II diagnostic connector under the instrument panel. After plugging in your tool, read out any fault codes that are found and write down the code(s), so the information isn’t lost when you clear the module’s memory.

You might find a code indicating one or more bad tire pressure sensors because there is no signal being received from those sensors. But, if you already checked each sensor with your TPMS tool and didn’t find any problems, you know the problem isn’t the sensors. Consequently, the only explanation is that the sensor signal is not getting through to the TPMS module. The problem could be a damaged or shorted antenna near the wheel or a wiring fault between the antenna and the TPMS module.

If you suspect the TPMS module is not receiving a good signal from one or more sensors, check the antenna wiring for continuity and problems such as shorts, opens or high resistance. A voltage drop test across any wiring connections should read 0.10 volts or less. A higher voltage drop reading indicates excessive resistance that is affecting the quality of the signal.

If the antenna wiring checks out, but the TPMS module is still generating a “no sensor signal” code, the fault is likely within the module itself. But, before you condemn the module and tell your customer the TPMS module needs to be replaced, make sure you check the TPMS module voltage supply and ground connections because low voltage can make any electronic module misbehave and act quirky.

On some vehicles, the signals to the TPMS module are shared or go through the keyless entry system, so a wiring problem that affects the keyless entry system could cause a problem with the TPMS. The TPMS module may be working fine but is not getting the right information from the keyless entry system. For that reason, always look up OE service information for the vehicle to understand how the TPMS operates — especially if you are having difficulty figuring out a problem.

A final factor not to overlook is the possibility of electromagnetic interference (EMI). EMI from another source such as adjacent wiring circuits, might be messing with the TPMS signals and confusing the system, causing a TPMS malfunction or false codes.

A step-by-step approach, a thorough inspection and operational knowledge of the system completes your diagnostic strategy. Check-mate.

You May Also Like

Fine-Tuning Your Wheel Balancing Process

The first step to a smooth ride and well-balanced tire has nothing to do with the balancer.

Courtesy of ShopOwner

The best tire in the world can’t fix a poor balance procedure and worn-out tooling. We have an opportunity to elevate the level of customer experience in our industry that takes nothing more than a few minutes of time and a commitment to using proper procedures and tools. And guess what? Your customer is more than willing to pay for it. Intrigued? Read on to learn what you can do in your shop to generate higher gross profit and lower comebacks.

Mercedes EQS Service Opportunities

EQ is the EV brand for Mercedes. It is the equivalent of Audi’s Etron or VW’s iD brands.

Diagnosing Electrical Problems With Your Multimeter

Transform your electrical diagnostics with these routine multimeter tests.

Multimeter
ADAS Calibration Tips

Here are 10 tips to follow during ADAS Calibration.

Repairing Wiring Harnesses

A guide to probing and poking.

Other Posts

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool
Upgrade Your Air System: It’s Easier Than You Think

Improving your shop airflow is only a benefit, unless you like to spend more time, work harder and make less money.

air flow tubes
Why ECU Reflashing Needs Certain Power Levels

A reflash power supply is not designed to jumpstart the vehicle.