When Should The Wheel Bearing Flange Be Replaced?

When Should The Wheel Bearing Flange Be Replaced?

The hub flange is ground zero for pulsation problems. Any runout in the flange will be magnified by the rotor. But, when do you replace a flange, stub axle or an entire hub unit? The answer can be confusing and will take some math and a micrometer.

The hub flange is ground zero for pulsation problems. Any runout in the flange will be magnified by the rotor. But, when do you replace a flange, stub axle or an entire hub unit? The answer can be confusing and will take some math and a micrometer. 
 
All flanges have some degree of runout. This is why there are tolerances in the service specification and in manufacturing. Most vehicles can tolerate a certain degree of runout before pulsation is felt by the driver. 
 
A flange may have up to .005” of runout and the bearings may have zero end play or noise. It is impossible to see damage with the naked eye.

This is why measuring with a dial indicator as part of a brake job is important. Damage to the flange is usually found on the backside of the flange where it meets the shaft and inner race. 
How Did Damage Occur?
A flange can be damaged by curb strikes, installation errors or even corrosion. Extreme or catastrophic flange damage due to a curb strike is rare. But, some curb strikes can tweak the flange and cause runout. In most cases, the wheel and knuckle will deform before the flange or stub axle. 
 
If a hub or bearing is over torqued, it can damage the flange and cause runout. It can also damage the bearings and the axle shaft. This type of runout can not be corrected by re-torquing the axle nut. The damage is permanent. 
 
Pitting and corrosion where the rotor mates to the flange can induce runout. If the corrosion is too great, replace the flange or bearing. Also, the flange can be damaged by excessive and uneven lug nut torque. 
  
How Much Is Too Much?
When diagnosing runout in a flange, a few things have to be taken into consideration before replacement. First, take into consideration the vehicle. On a small vehicle, .003” of runout in the flange may be too much. On a full-sized pickup this may be acceptable. 
 

Some OEMs may have a specification and replacement criteria for the flange runout, many do not. Always check for service information. 
Another consideration is the rotor. If you are using an on-the-car brake lathe, there is only so much meat on the rotor to remove to compensate for lateral runout. If too much material is removed, it could create a rotor that is thermally unbalanced. 
 
Most on-the-car brake lathes with automatic runout compensation will not allow the user to continue if the amount of lateral runout is too large. Either the machine will cite an error with the rotor or mounting of the lathe.
 

One option to save a flange is the rotor correction plate or shim. Flange runout can be corrected with tapered shims that are available to correct a runout of 0.003 inch (0.075 mm) to 0.009 inch (0.230 mm).
 
A runout of more than 0.005 inch (0.125 mm) at the bearing flange cannot be corrected by the use of a shim. The combination of rotor and bearing flange could prevent the rotor from being turned. Checking bearing flange runout should be performed after friction surface runout. Change the rotor position 180 degrees on the flange and check runout. If the high spot changes 180 degrees, the rotor could be OK or ready to turn after the bearing is shimmed.
 
Check the bearing endplay. Mark the relation of the rotor to the bearing flange. Mark the rotor high and low runout spots on the rotor friction surface; the low spot marked as zero and the high spot as the maximum value. Mark the high and low runout spots on the bearing flange with the same method and the rotor friction surface.  
 
Once you collected the data, the following comparisons should be made. Compare bearing flange to rotor runout position. If the shim cannot correct the runout, the bearing should be replaced. Check the rotor thickness. 
Replacement 
As a rule of thumb, runout greater than .005” for a light vehicle is a sign that the flange may be damaged or out of specification and further corrective action must be taken. 
 
If all attempts have been made to correct runout and it can’t be brought below .002” or recommended specification, the final option is replacement of the flange, stub axle or wheel bearing hub unit. 

You May Also Like

Autel to Bring OEM Repair Data to its Ultra Series Tablets

Autel partners with MOTOR Information Systems to provide an improved experience for users and more streamlined access to OEM repair information using MOTOR’s TruSpeed Repair.

Autel has announced that they have partnered with MOTOR Information Systems, to provide an improved experience for users and more streamlined access to OEM repair information using MOTOR’s TruSpeed Repair. MOTOR TruSpeed Repair will be available for integration into Autel’s diagnostics software on all North American Ultra series tablets including Advanced Driver Assistance System (ADAS) capable tools.

Scan Tools: Solving the Diagnostic Puzzle

“The fact is, the most expensive tool may not be the best tool for you. It depends on what vehicles you work on and what you want out of the tool.” – Dwayne Myers, Dynamic Automotive, Frederick, MD Related Articles – ISN’s Annual Tool Dealer Expo Gives Attendees Sneak Peek at New Products – Editor’s

ISN’s Annual Tool Dealer Expo Gives Attendees Sneak Peek at New Products

The TechShop team and more than 3,500 attendees from around the world recently joined Integrated Supply Network (ISN) at its 14th annual Tool Dealer Expo June 24-25 in Orlando, FL. There, suppliers launched new products and gave away more than $2 million in cash and prizes throughout the weekend event. Related Articles – Beyond the

Editor’s Notes: ‘The Rising Tide Lifts All Boats’

For the past year and a half, in addition to being editor of TechShop, I’ve also carried the role as editor of our student publication Tomorrow’s Tech, which is delivered to NATEF-certified automotive technical programs throughout the U.S. With this responsibility, I’m keenly aware of the industry’s need for the next generation of automotive service

Make Aluminum Welding Easier with Cebotech’s MIG Welders

All three of Cebotech’s MIG welders (models 301, 302 and 322) were designed to make aluminum welding easier. Related Articles – AMSOIL Introduces New OE 0W-40 100% Synthetic Motor Oil – BendPak Full-Rise Scissor Lift Delivers Two-Post Performance – CTA Tools Debuts Chrysler Cam Phaser Master Set – VVT & VVL They’re supplied with built-in welding programs

Other Posts

TPMS: Are Retrofits in Your Future?

Installing a retrofit kit can be performed with the tools and equipment you already own and use on a daily basis.

Tire tread
Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool
Upgrade Your Air System: It’s Easier Than You Think

Improving your shop airflow is only a benefit, unless you like to spend more time, work harder and make less money.

air flow tubes
PRT Heavy Duty Presenting Innovations at HDAW ‘24

PRT is exhibiting a full line of shocks and air springs for heavy-duty applications.