Why Oil Balancing Is Critical When Replacing A Compressor

Why Oil Balancing Is Critical When Replacing A Compressor

The purpose of oil balancing is to make sure the amount of oil in the A/C system remains at the correct level. The first thing to consider when performing the process is the amount of oil contained in the replacement compressor. This can vary from a full charge of oil (8 oz./236 mL), to a half charge of oil or no oil at all. If oil is contained in the replacement compressor, it will have to be removed and reinstalled in the correct amount to properly balance the system.

The purpose of oil balancing is to make sure the amount of oil in the A/C system remains at the correct level. The first thing to consider when performing the process is the amount of oil contained in the replacement ­compressor. This can vary from a full charge of oil (8 oz./236 mL), to a half charge of oil or no oil at all. If oil is contained in the replacement compressor, it will have to be removed and reinstalled in the correct amount to properly balance the system.
 
It’s also important to use the viscosity of oil recommended by the compressor manufacturer. If the compressor ­requires heavier-weight oil, such as PAG 150, but PAG 46, which is lighter-weight, is used, the result could be noisy compressor operation and ­premature wear.
 
After adding the oil to the compressor, a good service tip is to rotate the compressor clutch at least four turns prior to compressor installation. Rotating the clutch circulates oil through the compressor, which reduces the potential of compressor damage due to dry bearings, and it also reduces initial torque when the clutch is first ­engaged.
 

Rotating the compressor clutch is usually done by hand or with a spanner wrench. Another option is a compressor turning tool. On direct-drive compressors, the pulley and clutch are one and the same. 
 
The turning tool performs the same function as the spanner wrench, but it’s installed on the threaded hub of the clutch. After the turning tool is installed, use a wrench to turn the tool and clutch. The turning tool can be used on some clutches that cannot ­accept a spanner wrench because of clutch design, or where a solid grip by the spanner wrench cannot be achieved. The turning tool can also be used in place of the spanner wrench, providing an easier method of clutch rotation, and it can be done off or on the vehicle.
 
Never use a socket on the shaft nut or bolt to rotate the clutch. Doing so may affect the air gap between the clutch driver and compressor pulley, resulting in compressor issues.
 

You May Also Like

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

"The best investment is in the tools of one’s own trade.” – Benjamin Franklin. Needless to say, I agree. We all spend our careers investing in the tools we need to do the job, but, sometimes, based on the situation, the tools we choose differ and occasionally come from unexpected sources.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – New Small Stud Extractor Now Available from Mayhew Tools – Matco Debuts 5-Piece Purple Screwdriver Set – Mayhew Debuts New Fluorescent Handled Screwdrivers   OTC Genisys Touch – Quick scan, bidirectional control Snap-on VANTAGE Pro

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter
More Than A Scan Tool

Scan tools serve as indispensable diagnostic hubs, offering access to a wealth of resources, from OEM technical bulletins to community-documented repairs.

scan tool
Battling Stress and Burnout

Here are some quick tips for managing stress and avoiding burnout in the fast-paced automotive repair industry.

Nadine Battah
EV Acronyms and Terminology

Electric vehicles (EVs) are here to stay and there’s a lot to learn.

EV