Tech Tip: Life, Liberty and the Solution to Trouble Codes

Tech Tip: Life, Liberty and the Solution to Trouble Codes

Kathy enjoys hiking with her dogs. Recently, she traded in her old SUV for a 2005 Jeep Liberty that could comfortably carry the three of them. On a recent drive home from hiking in the mountains, Kathy noticed that the ABS lamp was on. She stopped by my shop a few days later, and after testing, we determined that the rear wheel speed sensor had failed.

By Eric Seifert
Automotive Technical Editor

Kathy enjoys hiking with her dogs. Recently, she traded in her old SUV for a 2005 Jeep Liberty that could comfortably carry the three of them. On a recent drive home from hiking in the mountains, Kathy noticed that the ABS lamp was on. She stopped by my shop a few days later, and after testing, we determined that the rear wheel speed sensor had failed.

Customers may experience a brake/ABS warning light or a Malfunction Indicator Lamp (MIL) illumination. On vehicles equipped with an Anti-Lock Brake System (ABS), a red brake light and/or an amber ABS light may illuminate and remain on. On vehicles NOT equipped with ABS, the MIL may illuminate. The MIL may be due to DTC P0501 – Vehicle Speed Signal Performance/Vehicle Speed Sensor Plausibility.

The condition may be due to a rear differential-mounted wheel speed sensor that is contaminated by the rear axle fluid. If using the Diagnostic Trouble Code Tests available in ALLDATA determines that the sensor requires replacement, perform the Repair Procedure.

Replacement of the rear wheel speed sensor and axle fluid will require the following parts:
• (1) 56041393AA Rear Wheel Speed Sensor;
• (1) 05086373AA Speed Sensor O-Ring;
• 05013477AA Axle RTV;
• 04897151AB Brake Parts Cleaner;
• (3) 05010320AA Mopar Synthetic Gear Lubricant 75W-90OR (3) 04874469 Mopar Synthetic Gear & Axle Lubricant 75W-140 (if towing); and
• (1) 04318060AB Limited Slip Additive (if Trac-Loc equipped).

Applicable Vehicles: 2005 (KJ) Liberty/Cherokee

Repair Procedure:
(Review safety procedures in the ALLDATA system before beginning)

1. Disconnect and isolate the negative battery cable from the battery.

2. Raise the vehicle on a suitable lift.

3. Remove the rear axle differential housing cover.

4. Thoroughly clean the axle, differential and differential cover of old oil, debris and RTV.

5. Remove the rear wheel speed sensor electrical connector. Remove the sensor from the axle.

6. Install the new 0-ring, P/N 05086373AA, to the new rear wheel speed sensor.

7. Lubricate the new rear wheel speed sensor and 0-ring.

8. Install the new rear wheel speed sensor, P/N 56041393AA, to the axle. Tighten the attaching bolt to 9 Nm (80 in. lbs.).

9. Verify that the seal is securely in place between the sensor and wiring connector. Install the sensor electrical connector to the sensor.

10. Apply a bead of Axle RTV sealant, p/n 05013477AA, to the differential housing cover.

CAUTION: If cover is not installed within 3 to 5 minutes of new RTV sealant application, the cover must be cleaned and new RTV sealant applied. Failure to follow instructions will cause a leak.

11. Install the cover and identification tag. Tighten cover bolts in a criss-cross pattern to 41 Nm (30 ft. lbs.).

12. If not already removed, remove the fill plug.

13. If axle is equipped with a Trac-Lok differential, install 4 oz. of Limited Slip Additive to the differential.

14. Fill the axle differential with the correct axle lubricant.

15. Install the fill plug.

16. Verify that the rear wheel speed sensor and differential housing cover is correctly installed.

17. Lower vehicle.

18. Connect the negative battery cable to the battery. Set the clock to the correct time.

Written by ALLDATA Technical Editor, Eric Seifert. Eric is an ASE certified Master Technician and Engine Machinist. He is a graduate of the De Anza College Automotive Technology Program, with 20 years of independent shop and parts store experience.

For additional information, visit www.alldata.com.

You May Also Like

#8 Shop Air Systems

An aging air system can affect the output of air tools and equipment.

Shop Aire Systems

An aging air system can affect the output of air tools and equipment. Often the tools are blamed when a lack of air from corroded, restrictive piping is the culprit. Testing the efficiency of your air system is important, and restoring proper airflow and pressure leads to improved equipment and technician efficiency, as well as energy savings. Updating old or building new, your air system is the heart of your shop.

Mobis Starts Construction of EV Battery System Plant in Spain

The new EV battery system plant will supply Volkswagen and is aiming for mass production by 2026.

#7 Wrenches

Wrenches are the core of every tool collection.

Wrenches
Maverick Tire Changer: Bead Massage

The bead massage feature on the Maverick tire changer helps with better tire and wheel fitment for balancing.

Navistar Surpasses 100 Authorized EV Dealers

Navistar will have more than 30% of its dealer locations ready to support the sale and service of both International and IC Bus EVs.

Other Posts

ADAS: Coming of Age

ADAS are categorized into levels, determined by the amount of automation for any given system.

Hunter Maverick Tire Changer: 19.5-inch Tire Service

Learn to handle 19.5-inch wheels, which are common on some delivery vehicles, with Hunter’s Maverick tire changer.

#6 Multimeter DC Voltage Testing

Diagnosing electrical system problems isn’t always easy, and guessing is never an option.

LG Energy Solution’s Battery Facility to be Completed by 2026

LG Energy Solution said the cylindrical battery plant, called LG Energy Solution Arizona, will produce 46-Series batteries for EVs.