Tech Tip: Chevy Blazer's Engine May Rattle Between 1,800 and 2,200 rpm

Tech Tip: Chevy Blazer’s Engine May Rattle Between 1,800 and 2,200 rpm

Some customers may comment on a rattle-type noise coming from the engine at approximately 1,800 to 2,200 rpm. The spark, rattle-type noise may be caused by torsional vibration of the balance shaft. If detonation noise is present, perform detonation/spark knock diagnostics first.

Some customers with the vehicles mentioned below may comment on a rattle-type noise coming from the engine at approximately 1,800 to 2,200 rpm.

Models affected:
• 1996-2003 Chevrolet Astro, Blazer, Express, S-10, Silverado;
• 1996-2003 GMC Jimmy, Safari, Savana, Sierra, Sonoma; and
• 1996-2001 Oldsmobile Bravada — with 4.3L V6 engine (VINs W, X – RPOs L35, LU3).

The spark, rattle-type noise may be caused by torsional vibration of the balance shaft. If detonation noise is present, perform detonation/spark knock diagnostics first.

Install a new tensioner assembly kit using the procedure below.

  1. Remove the engine front cover.
  2. Remove the crankshaft sensor reluctor ring and line up the timing marks on the crank gear and camshaft gear.
  3. Remove the camshaft gear and chain. For model years 1996-’98, remove the crankshaft sprocket using J 5825-A.
  4. Pull the shipping pin and discard. Remove the nylon timing chain tensioner blade from the timing chain tensioner bracket.
  5. Position the bracket on the front of the engine. The upper two attaching holes of the bracket will line up with the center two engine front cover bolt holes. The lower bracket holes will line up with the engine front cover alignment holes. See Figure 1.
  6. Use a hammer and the J 46165 Pin Driver to install the dowel pins through the two lower holes in the bracket and into the engine block. Make sure that the bracket is held firmly in place before proceeding.
  7. For model years 1996-’98, install a roller-type timing chain set. Install the crankshaft sprocket using the J 5590 Crankshaft Gear Installer.
  8. Install the timing chain around the crankshaft sprocket and position the timing chain to the driver’s side of the engine.
  9. Install the nylon timing chain tensioner guide onto the timing chain tensioner bracket pin and position the top of the guide under the tab at the top of the bracket.
  10. Install the camshaft sprocket into the chain and then to the camshaft. Install the bolts finger-tight. Make sure the timing marks are aligned, then tighten the camshaft sprocket bolt to 25 Nm (18 lb.-ft.).
  11. Install the crankshaft reluctor ring.
  12. Install the engine front cover and place a washer under the two center cover bolts that extend through the tensioner bracket. These washers are required to maintain the proper crush on the engine front cover seal. Tighten the bolts to 12 Nm (106 lb.-in.).

Courtesy of ALLDATA.

For additional information, visit www.alldata.com.

You May Also Like

CITGO Enters EV Space with Pilot Program Launch

The CITGO location on 11 Mile Road in Michigan now offers both regular transportation fuel and EV charging stations.

CITGO Petroleum Corporation, along with marketer Folk Oil Company, recently launched an electric vehicle (EV) charging pilot program they said is designed to meet the needs of EV drivers in Battle Creek, Mich. The CITGO location at 15551 11 Mile Road now offers both regular transportation fuel and EV charging stations. For added consumer convenience, EV chargers include both Charging System (CCS) and the North American Charging Standard (NACS) plugs, the companies said.

TS Toolbox Guide February 2024

Here’s a look at some of the core feature and modern frills to consider when it’s time to move into a new office.

toolbox guide illustartion
Stellantis Increasing Production of Electric Drive Modules

The company will add EDM production in Szentgotthard, Hungary, targeted to begin in late 2026.

Embracing Cutting-Edge Solutions the Industry has to Offer

Embracing cutting-edge solutions is strategic and imperative for technicians navigating the constantly changing landscape of automotive maintenance and repair.

Nadine Battah
Tool Time Podcast: Clore Automotive

Jim O’Hara from Clore Automotive joins Nadine Battah and Eric Garbe.

Other Posts

TechShop, ShopOwner Offer $50 For Good Guesses

Guess the Tool for a chance at cold hard cash!

GM, Honda Begin Volume Production of Fuel Cell Systems

GM and Honda will produce fuel cells that will be two-thirds less expensive compared to Honda’s 2019 Clarity fuel cell.

Toyota Bringing Battery EV Production to Kentucky

It will invest $1.3 billion at its flagship Kentucky facility for future electrification efforts, including assembly of an all-new, three-row battery electric SUV for the U.S. market.

Repairify Announces Executive Leadership Changes

The company has named Craig Edmonds as president of asTech among other executive appointments.