Tech Tip: Diagnosing Popping Sound Coming from Front Hub/Half Shaft Area on PT Cruisers and Neons

Tech Tip: Diagnosing Popping Sound Coming from Front Hub/Half Shaft Area on PT Cruisers and Neons

The vehicle may exhibit a popping/clicking/snapping/ticking sound from the front hub/half shaft area during acceleration after Drive to Reverse or Reverse to Drive shifts. The sound may also be present while turning and accelerating from a stop. In order to determine if the popping/clicking/snapping/ticking sound is coming from the front hub/half shaft interface, perform the following procedure.

Vehicles:
• 2000-2005 Neon
• 2001-2004 Chrysler PT Cruiser

Symptom/Condition:
Vehicle may exhibit a popping/clicking/snapping/ticking sound from the front hub/half shaft area during acceleration after Drive to Reverse or Reverse to Drive shifts. The sound may also be present while turning and accelerating from a stop.

Diagnosis:
In order to determine if the popping/clicking/snapping/ticking sound is coming from the front hub/half shaft interface, perform the following procedure:

1. Raise the vehicle on an appropriate hoist and remove both front wheels.

2. Remove the cotter pin, nut lock and wave washer from the end of both half shafts.

3. With the vehicle’s brakes applied to keep the hub from turning, loosen both half shaft nuts to zero torque.

4. With the service brake applied, shift the vehicle from Drive to Reverse and Reverse to Drive. Once the transmission is engaged in gear, raise the engine speed to 1800 rpm.

5. If the sound is not present, perform the Repair Procedure. If the sound is still present, the source of the sound is elsewhere. Further diagnosis is required.

Repair Procedure:
1. Raise the vehicle.

2. Remove the half shaft nut.

3. Remove the wheel and tire assembly from the vehicle. Refer to the service information.

4. Remove the two front disc brake caliper adapter to steering knuckle attaching bolts (See Figure 1).

5. Remove the disc brake caliper assembly from the steering knuckle. The caliper assembly is removed by first rotating the top of the caliper assembly away from the steering knuckle and then removing the bottom of the assembly out from under the machined abutment on the steering knuckle.

6. Support the disc brake caliper assembly by using a wire hook and suspending it from the strut assembly (See Figure 2).

Note: Do not allow the brake caliper assembly to hang by the brake flex hose.

7. Remove the brake rotor from the hub and bearing assembly.

8. If the vehicle is equipped with eccentric bolts attaching the steering knuckle to the strut assembly, proceed to next step. If not, proceed to step 10.

9. Mark the head of the eccentric bolt and the strut, so that the bolt can be installed in the same position later.

10. Remove the wheel speed sensor bolt.

11. Remove the steering knuckle-to-strut attachment bolts from the steering knuckle (see Figure 3).

12. Pull the steering knuckle from the strut clevis bracket.

Note: Care must be taken not to separate the inner CV joint during this operation. Do not allow half shaft to hang by inner CV joint after removing outer CV joint from the hub/bearing assembly in steering knuckle. The outboard end of the half shaft must be supported.

13. Pull the steering knuckle assembly down and away from the outer CV joint while pulling the CV joint out of the hub bearing.

14. Support the outer end of the half shaft assembly.

Note: The rubber gasket is to be installed as is (after removing the paper backing). The gasket should not be cut in any way.

15. Slide the gasket/washer, p/n 04809863, over the CV joint splines to the CV joint surface, item 2, shown in Figure 4.

16. Grasp the inner tripod joint and interconnecting shaft. Forcefully push the tripod joint into side gear of the transaxle. Be sure the snap-ring is engaged with the transaxle side gear.

17. Clean all debris and moisture out of the steering knuckle in the area where the outer CV joint will be installed into steering knuckle.

18. Clean the CV joint surface.

19. Ensure that the front of the outer CV joint which fits against the face of the hub and bearing is free of debris and moisture before installing the outer CV joint into the hub and bearing assembly.

20. Slide the half shaft back into the hub assembly.

21. Install the wheel speed sensor bolt and torque it to 12 Nm (105 in. lbs.).

Caution: The steering knuckle to strut assembly attaching bolts are serrated and must not be turned during installation. Install nuts while holding bolts stationary in the steering knuckle.

Caution: If the vehicle being service is equipped with eccentric strut assembly attaching bolts, the eccentric bolt must be installed in the bottom (slotted) hole on the strut clevis bracket (See Figure 5).

22. Install the steering knuckle in the clevis bracket of the strut assembly. Install the strut to steering knuckle attaching bolts. If the eccentric bolt and strut was marked in step 9, align the marks. Tighten both bolts to a torque of 88 Nm (65 ft. lbs) plus an additional 1/4 turn.

23. Install the brake rotor on the hub and bearing assembly.

24. Install the disc brake caliper assembly on the steering knuckle. The caliper is installed by first sliding the bottom of the caliper assembly under the abutment on the steering knuckle, and then rotating the top of the caliper against the top abutment.

25. Install the disc brake caliper adapter to steering knuckle attaching bolts (Figure 1). Tighten the disc brake caliper adapter bolts to a torque of 169 Nm (125 ft. lbs.).

26. Clean all foreign matter from the threads of the outer CV joint. Install the washer and half shaft nut on half shaft and securely tighten the nut (the nut will be torqued later).

27. Install the front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all the nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 Nm (100 ft. lbs.).

28. Repeat steps 2 through 27 on the other side of the vehicle. When steps 2 through 25 have been completed on both sides of the vehicle, lower the vehicle.

29. With the vehicle’s brakes applied to keep the hub from turning, tighten the hub to a torque of 244 Nm (180 ft. lbs.).

30. Install the spring wave washer on the end of the half shaft.

31. Install the hub nut lock, and a new cotter pin. Wrap the cotter pin prongs tightly around the hub nut lock as shown in Figure 6.

32. Repeat steps 29 through 31 on the other side of the vehicle.

Technical service bulletin courtesy of Mitchell 1.

For more information on Mitchell 1 products and services, automotive professionals can log onto the company’s website at www.mitchell1.com.

You May Also Like

Toyota, Lexus Offer Lower Emissions EV Charging Program

Toyota has entered into an agreement to provide health and environmental impact data to Toyota and Lexus customers.

Courtesy of The Buzz by David Sickels

Toyota Motor North America (Toyota) has recently entered into an agreement with WattTime, a company that develops clean energy data-driven insights, software, and tools, to provide certain health and environmental impact data to Toyota and Lexus customers with eligible vehicles and enable them to find ideal charging times to reduce emissions when charging at home.

Lexus and Toyota Camera Calibration (VIDEO)

Joe Keene discusses how to calibrate the camera on a 2021 Lexus UX where the camera was removed and reinstalled.

Autel Expands Presence in Asia, Australia

Autel expands in the Asia-Pacific region with new energy vehicle charging solutions for residential and commercial use.

Get To Know The Equipment and Tool Institute (ETI)

Executive director of ETI sits down with editor Nadine Battah to discuss ETI and the events it hosts.

Utilizing NVH Tools

Technology has been improving on NVH tools over the years.

Other Posts

Charging Ahead With EV Opportunities

New data shows there will be room for – and a need for – products for both incoming electric and ICE vehicles.

Streamlight Stinger Color-Rite Rechargeable Flashlight

TechShop Reveal provides a 360 product video highlighting the industry’s latest innovations.

Why Is This Brand New PS Pump So Noisy?

There are several questions which you should ask yourself in this scenario. This video is sponsored by Rislone.

DOE Puts $48M Toward Improving America’s Power Grid

This effort aims to better control grid power flow to avoid outages, which costs the economy $150 billion annually.