Tech Tip: Rough Road Leads to Squeaky Silverado

Tech Tip: Rough Road Leads to Squeaky Silverado

During normal operation, certain vehicles may exhibit a squeaking noise that can be traced to the rear leaf springs. While this noise is an operating characteristic of leaf springs, the frequency and severity of this noise will be affected by the roads on which the vehicle is driven. The noise may be due to debris getting between the leaf springs.

By Eric Seifert
Automotive Technical Editor

Chris used his 2001 Chevy Silverado to pick up some sod for a friend. The rear of his truck has been squeaking ever since taking that bumpy road to the sod farm. Chris was relieved to learn that there was a simple cure for the annoying squeak.

During normal operation, certain vehicles may exhibit a squeaking noise that can be traced to the rear leaf springs. While this noise is an operating characteristic of leaf springs, the frequency and severity of this noise will be affected by the roads on which the vehicle is driven. The noise may be due to debris getting between the leaf springs.

To correct this condition, lubricate the rear leaf springs with GM P/N 12345996 (in Canada, use P/N 10953501) grease, using the following procedure.

Applicable Vehicles
• 1999-2007 Chevrolet Silverado (Classic)
• 1999-2007 GMC Sierra (Classic)

Repair Procedure
(Review safety procedures in the ALLDATA system before beginning)

Important: It has been found that the application of grease to the rear leaf springs does a better job of preventing the noise from re-occurring than replacement of the spring.

1. Raise the vehicle on a frame lift-type hoist.

2. Inspect the springs for damage. If none is found, proceed to the next step.

3. Pressure wash the rear leaf springs to remove as much dirt and grit as possible.

4. Dry the springs with compressed air.

5. Apply a liberal amount of grease, GM P/N 12345996 (in Canada, use P/N 10953501), under the front and rear tip inserts for the #2 and #3 leaves, on top of the tip inserts, and in between the #1 and #2, and #2 and #3 leaves, as indicated. A screwdriver can be used to gently pry up the tip insert; however, a rag around the screwdriver must be used to prevent damage to the spring. Use a flat-bladed tool, such as a gasket scraper to properly distribute the grease.

6. Lower the vehicle to the ground and test drive to verify the repair.

Inform the customer that this will offer relief, but it is by no means a lifetime repair. Periodic cleaning and grease re-application may be necessary throughout the life of the vehicle.

For 1500 Series (1/2 ton) models only: On vehicles built prior to October 2004, if the above procedure does not correct this noise, it could be caused by an incorrectly dimensioned splay clip (the band holding the ends of the leafs together) that interferes with the leaf springs. A 5 mm (0.197 in) wider splay clip was introduced in early 2005 model year to provide additional clearance. To correct this concern, replace the rear leaf spring assembly.

Written by ALLDATA Technical Editor, Eric Seifert. Eric is an ASE certified Master Technician and Engine Machinist. He is a graduate of the De Anza College Automotive Technology Program, with 20 years of independent shop and parts store experience.

For additional information, visit www.alldata.com.

You May Also Like

Get To Know The Equipment and Tool Institute (ETI)

Executive director of ETI sits down with editor Nadine Battah to discuss ETI and the events it hosts.

ETI is an association of automotive tool and equipment manufacturers, technical information providers, and training organizations.

In this episode of the Striking Point video podcast series, editor Nadine Battah sits down with ETI's executive director, Brian Plott, to discuss what ETI is and the events they host.

Utilizing NVH Tools

Technology has been improving on NVH tools over the years.

Charging Ahead With EV Opportunities

New data shows there will be room for – and a need for – products for both incoming electric and ICE vehicles.

Streamlight Stinger Color-Rite Rechargeable Flashlight

TechShop Reveal provides a 360 product video highlighting the industry’s latest innovations.

Why Is This Brand New PS Pump So Noisy?

There are several questions which you should ask yourself in this scenario. This video is sponsored by Rislone.

Other Posts

DOE Puts $48M Toward Improving America’s Power Grid

This effort aims to better control grid power flow to avoid outages, which costs the economy $150 billion annually.

Autel, Repairify Announce Collaboration Agreement

Repairify will integrate within Autel’s Remote Expert platform.

Job Corps, Mercedes Partner to Offer EV Technician Training

The agreement will allow Mercedes-Benz USA to develop the curriculum and train Job Corps instructors to deliver it.

BendPak Announces Death of Gary Henthorn

Son of BendPak founders established Dannmar, MaxJax and Garage Equipment Supply.