Directions: The Impact of HF0-1234yf on Service Shops

Directions: The Impact of HF0-1234yf on Service Shops

According to the new refrigerant's developers, there are chemical differences between HFO-1234yf and the current R-134a system. As a shop owner, you'll need to learn the Safety, Equipment and Charging Issues surrounding this new refrigerant.

Last month, we discussed the industry’s move toward a new refrigerant — HFO-1234yf — for mobile air conditioning systems. The move is expected to begin in European vehicles and eventually become common in domestic vehicles (See Directions, March 2010 issue.)

While we discussed the reasons why the change was being implemented, what the product will accomplish, who is part of the new refrigerant movement and where and when it will occur, this month, we’ll take a look at how all that can effect your shop, technicians and bottom line.

What It Means for Shops and Techs
In a presentation with MACS and DuPont officials in January in France, it was explained that shops should expect some potential service differences with HFO-1234yf.

The most obvious is the need for service shops to purchase and operate new recovery, recycling and system recharging equipment. Shops will not be able to use the same R-134a refrigerant equipment when servicing the new HFO-1234yf systems.

Equipment manufacturers we spoke to said they are currently in development of new equipment to handle the HFO-1234yf systems and adhere to updated SAE guidelines for such equipment.

It also was noted that refrigerant identifiers and updated leak detection equipment would be necessary for shops to service these systems.

Safety Issues
According to the new refrigerant’s developers, there are chemical differences between HFO-1234yf and the current R-134a system.

For example, HFO-1234yf is mildly flammable, so technicians and shop staff would need training to understand the precautions that need to be followed when used with other flammables (i.e. gasoline, oil).

Also, since the new refrigerant is heavier than air, care must be taken in the shop in low-lying areas (such as workshop/oil drain pits, shafts or cellar exits), which may cause released refrigerant to pool. Service technicians should not smoke or have any open flame present while working on these refrigerant systems or in the low-lying areas where HFO-1234yf could accumulate.

One of the proposals is to require work areas to be adequately ventilated and fans available if needed.

Be Mindful of Mix-Ups
Cross contamination is also expected to be an issue in the early stages of HFO-1234yf use in vehicles, as DIYers may charge non-approved refrigerants into these A/C systems.

The outcome of cross-contamination could be system failure or system misdiagnoses if the technician isn’t informed of the mixed refrigerants in a vehicle’s A/C system.

Product manufacturers also will take precautions to reduce cross-contamination at the shop. Currently, packaging for R-134a refrigerant is in light blue, 30-lb. returnable containers.

Packaging color for HFO-1234yf containers (also offered in 30-lb. returnable containers) will be white with red band around it.

And, don’t expect to perform any R-134a to HFO-1234yf retrofits. While R-12 to R-134a
retrofit jobs at service shops were a “hot topic” in the mid-1990s, the EPA said R-134a product would remain available to service existing systems.

That concept may work better this time around. While retrofits in the 1990s did provide shops additional revenue and service opportunities, many customers felt the new systems didn’t cool their vehicle cabins efficiently. This is because those vehicles were designed to use the (better cooling) R-12 systems, rather than a less-efficient R-134a system.

And, let’s not forget the “mystery refrigerant” fiasco of the late ’90s, as DIYers never really knew for certain what was in that container of bootlegged R-12 that they used to charge their system. Incidents like that were tough on shop owners when they found out their recovery equipment became contaminated or they had to dispose of a flammable “cocktail” of refrigerant recovered later from that vehicle’s system.

Since manufacturers will continue to produce R-134a with no interruptions until these systems slowly phase themselves out, the issues of bootlegged and unknown refrigerants should diminish.

SAE and the EPA also explained that HFO-1234yf systems will also use specific fittings that are different from R-134a units in an effort to minimize accidental cross-contamination.

And, the EPA also stressed that HFO-1234yf refrigerant system components should not be replaced with ones removed from a system that uses another type of refrigerant (R-134a) or from a salvaged vehicle.

Charging Costs
Finally, customer feedback is going to be something you will need to deal with. According to manufacturers, the new refrigerant will cost more to produce. While no pricing has been introduced until the market dictates mass production of the refrigerant, it is estimated by some that HFO-1234yf could cost anywhere from  $35-$60 a pound.

So, you can pretty much expect some customers who have their HF0-1234yf systems serviced down the road will give you an earful when they get a service repair estimate. When dealing with such customers, just remember to “keep your cool.”  

 

You May Also Like

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

TEXA has released a major update IDC5 CAR 76.5.0 which enhances Car, Supercar and Light Commercial IDC5 diagnostic features & coverage. This latest software update enables more efficient troubleshooting, enhances existing special functions and topology module mapping features, while increasing technical information accessibility that is essential for accurately completing complex workshop operations. IDC5 CAR 76.5.0 includes the update of 37 makes, including electric and hybrid vehicles, while increasing the coverage of ADAS calibration, enhancing the visual live data "DASHBOARD" screens and other interactive technical information features like wiring diagrams, maintenance guides and component location diagrams.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Lisle Low Profile Fuel Line Disconnect – Dent Fix Soft-Shock Mallet DF-SM76 Reduces Damage – New ProMAXX Diesel Fuel Injector Seal Puller/Saver ProKits   OTC Genisys Touch – Quick scan, bidirectional control Snap-on VANTAGE Pro

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

Identity Crisis and the Rise of the Specialist

Is it time to move on from ‘technician’ and become ‘specialists’ in the shop?

ISN Expands Freedom Program for Mobile Tool Dealers

ISN’s Freedom Program is designed to provide experienced, successful mobile tool dealers with support to become an independent mobile dealer and expand their growth.

Snap-on Continues to Offer Free Weekly Product Training Sessions

The online training and question and answer sessions are free of charge.

TechShop, ShopOwner Offer $50 For Good Guesses

Guess the Tool for a chance at cold hard cash!