Air Update: Maintaining Your Pneumatic Tools

Air Update: Maintaining Your Pneumatic Tools

Professional-grade air tools can be very expensive and represent a sizable investment. But the tools can last many years with the proper care – and a clean air supply.

Air UpdateAir tools are profitable timesavers for professional technicians because pneumatic muscle speeds up disassembly and reassembly. That allows most technicians to beat flat rate and get paid for more billable hours. Professional-grade air tools can be very expensive and represent a sizable investment. But the tools can last many years with the proper care – and a clean air supply.

DIYers also like pneumatic tools because the tools save effort. A pneumatic impact wrench can loosen a stubborn fastener that otherwise might be nearly impossible to take apart. DIY tools are typically much less expensive than their professional counterparts. Even so, they also require the same level of maintenance and protection to provide reliable service.

One thing all tools require is a clean, dry air supply. A hard-working air tool can use quite a few cubic feet of air per minute. So it’s important the air entering the tool is free of contaminants.

The biggest threat to pneumatic tools is moisture. Small droplets of water can form inside a compressor storage tank when outside air is pumped into a tank. The moisture comes from humidity in the air, and condenses into little droplets because the compressed air becomes saturated with more moisture than it can hold. There’s no avoiding it because humidity is everywhere, even in relatively dry climates like Arizona. Humidity varies according to the weather and temperature, and can reach 100% during rainy, wet weather.

Water inside a metal compressor tank is bad news because it can cause corrosion. If the water is not removed on a regular basis (usually daily) by opening the drain valve on the bottom of the tank so air pressure can blow out the moisture, it will eventually rust the inside of the tank.

This can create dangerously weak areas inside the tank that may blow out when the tank is under pressure. What’s more, the flakes of rust can come loose and find their way into the air supply line that carries air to pneumatic tools, causing wear and damage to the tools.

Even if the compressor tank is drained daily, water and humidity inside the tank can still pass through the air supply line and attack pneumatic tools from the inside.

One way to protect pneumatic tools from contamination and damage is to install a special filter in the compressor air supply line. These filters will not only stop any rust or other debris that finds its way into the air line, but will also prevent moisture from getting through.

Many repair shops and new car dealerships have these filters installed in their shop air supply lines for this very reason. The filters keep the lines clean, and protect their technicians’ pneumatic tools from premature wear and damage. DIYers can also install a similar type of air filter on a home compressor to achieve the same results.
Technicians who use these aftermarket air supply filters report as much as a four-fold increase in tool and equipment life, and a dramatic reduction in corrosion-related maintenance and repair. By protecting their tools from moisture in the air supply line, they eliminate the single largest cause of air tool failure.
Most compressors do not include equipment to minimize moisture, and even compressors with drying solutions cannot completely prevent the buildup of water vapor inside. In order to prevent water from getting into the air supply line, water vapor must be stopped with a filter. And because water vapor is always present in the air, moisture control filtration and regular maintenance is always needed.

Other steps that should be taken to maintain and prolong the life of pneumatic tools include the following:

1. Oil pneumatic tools regularly. Use a quality oil designed for this purpose only (not motor oil).

2. Tools should be serviced yearly by a professional.

3. Air quality should be checked regularly (which means checking for water in the air supply line).

4. If any sign of contamination is found in the line, tools or filter, it’s time to replace the filter.

5. If rust flakes are found inside a filter, the tank should be inspected to make sure it is safe (replacement may be necessary if it is full of rust).

You May Also Like

Battery Chargers & Testers – Keeping the Charge Alive

Keeping a vehicle’s battery charged and ready to go is more important than ever.

As vehicle manufacturers steadily increase the amount of electronic entertainment and convenience features on vehicles, the more electrical power is needed to operate them. That means keeping the vehicle’s battery – the main reservoir of electrical power – always charged and ready to go. Although a battery is built to last a couple of years, once in a while, it may “die,” due to extreme cold weather, or prolonged lack of use, the latter being the most common reason, said one shop owner. This may not always mean that something is wrong with the battery or that it needs to be replaced; it might just be “depleted.”

Top 5 Tools: Steve Molnar, Suburban Auto Service

Identifix, Snap-on and Matco Tools are named as the makers of this top technician’s top five favorite tools.

Diagnosing Ford EGR System Modules

The EGR system module is one of Ford’s latest EGR systems for gasoline engines. It is an EGR valve, EVR, MAP and DPFE sensor rolled into one package. Grab your scan tool, contributing writer Glen Beanard explains how to diagnose problems in these systems.

Air Update: Buying a New Air Compressor

Routine maintenance makes a huge difference in lifecycle expectancies of our tools and equipment. But even with the best maintenance schedules, you need to replace your capital investments at some point.

Humble Mechanic: Thinking Like A Diagnostic Technician

Charles’ diagnostic processes may be very different from yours, which may be very different from the tech that works next to you. But the end goal is always the same: Fix the car right the first time, and do it as fast as possible.

Other Posts

Snap-on Lights the Way

Snap-on lights provide techs illumination in dark spaces.

Inductor Max: Experience the Power of Induction Heating

Rapidly heat components while eliminating the dangers of an open flame.

Hunter Center-Clamp Tire Changer Adjusts to 3 Heights

The new tire changers, which include a mobile version, meet the need for shop productivity in limited space.

ProMAXX Tool Provides Solution for FCA U90 Emissions Recall

Bullit adaptable bolt repair ProKit and thread repair kit helps technicians quickly perform repair.