Tech Tip: Diagnosing a Nissan Altima with the Check Engine Light On

Tech Tip: Diagnosing a Nissan Altima with the Check Engine Light On

The engine runs rough, gas mileage is down and more importantly the "check engine" light is on. That little illuminated check engine light strikes fear in the hearts and minds of the average vehicle owner - it's supposed to. Otherwise, people would keep driving their vehicles as long as they could, eclipsing the light with a piece of electrical tape.

The engine runs rough, gas mileage is down and more importantly the "check engine" light is on. That little illuminated check engine light strikes fear in the hearts and minds of the average vehicle owner – it’s supposed to. Otherwise, people would keep driving their vehicles as long as they could, eclipsing the light with a piece of electrical tape. That wouldn’t be good for our air quality. Luckily, most good citizens are of the belief that if that check engine light is on, not only is the vehicle going to leave them stranded at the most inopportune time, a plague could befall their entire family and their subsequent heirs for generations.

To the professional technician however, the "check engine" light is a sign that there may be a significant problem, but it’s probably nothing that’s going to change the course of history. With the help of ongoing education, a good scan tool and accurate diagnostic information, thousands of technicians repair "check engine" light related problems daily.

So why does something as simple as an engine misfire warrant a tech tip? Many techs assume that because automotive technology has become more complex, drivability problems have become more complex. In some ways they have, but on the other hand, sometimes facilitating a timely repair is just a matter of checking the simple basics.

In keeping with the simplicity theme, let’s cut straight to the details of this tech tip. If any of the applied vehicles (listed below) have a check engine light on, diagnostic trouble codes P0300 through P0304 (cylinder misfire) stored and/or exhibit a rough running engine, check the spark plug wire tubes and boots as follows:

Applied Vehicles:
• 1995-97.5 Altima (U13) models built before: 1N4BU31D3VC245368; and
• 1998 Altima (L30) models built before: 1N4DL01D8WC165916.

Applied Dates:
• 1995-97.5 Altima (U13) models built before March 5, 1997; and
• 1998 Altima (L30) models built before October 28, 1997.

PROCEDURE:
1. Remove the spark plug wires and inspect for water in the spark plug holes. If water is in the spark plug holes, perform the following steps:
• Remove water from the spark plug holes.
• Insert a paper clip through the steam vent hole in the spark plug wire boots to insure the holes are clear (see Figure 1).

NOTE: The steam vent hole allows water vapor to escape if water becomes trapped in the spark plug hole.

• Inspect spark plug wire boots for cracks, hardening or deformities that could prevent sealing between the boots and the camshaft (valve) cover.
• Replace all spark plug wires if one or more of the boots show signs of cracks, hardening or deformities.

If the spark plug holes are dry and the spark plug wire boots are in good condition, proceed with step 2.

2. Inspect the entire surface of each spark plug wire tube for pinholes and/or cracks (see Figure 2).

• If one or more spark plug wire tubes have pinholes and/or cracks, replace all of the spark plug wires.

And there you have it — in these complex times, a simple solution to a simple problem. And all that was required was an ongoing education, a good scan tool and accurate diagnostic information. It’s up to you to provide the first two items. As for the last item — I’m always glad to help.

Written by ALLDATA Technical Editor, Rich Diegle. Rich is an Advanced Engine Performance Certified and ASE Master Technician with an Associate of Arts degree in automotive technology and 22 years of dealership and independent shop experience.

For additional information, visit www.alldata.com.

You May Also Like

Get To Know The Equipment and Tool Institute (ETI)

Executive director of ETI sits down with editor Nadine Battah to discuss ETI and the events it hosts.

ETI is an association of automotive tool and equipment manufacturers, technical information providers, and training organizations.

In this episode of the Striking Point video podcast series, editor Nadine Battah sits down with ETI's executive director, Brian Plott, to discuss what ETI is and the events they host.

Utilizing NVH Tools

Technology has been improving on NVH tools over the years.

Charging Ahead With EV Opportunities

New data shows there will be room for – and a need for – products for both incoming electric and ICE vehicles.

Streamlight Stinger Color-Rite Rechargeable Flashlight

TechShop Reveal provides a 360 product video highlighting the industry’s latest innovations.

Why Is This Brand New PS Pump So Noisy?

There are several questions which you should ask yourself in this scenario. This video is sponsored by Rislone.

Other Posts

DOE Puts $48M Toward Improving America’s Power Grid

This effort aims to better control grid power flow to avoid outages, which costs the economy $150 billion annually.

Autel, Repairify Announce Collaboration Agreement

Repairify will integrate within Autel’s Remote Expert platform.

Job Corps, Mercedes Partner to Offer EV Technician Training

The agreement will allow Mercedes-Benz USA to develop the curriculum and train Job Corps instructors to deliver it.

BendPak Announces Death of Gary Henthorn

Son of BendPak founders established Dannmar, MaxJax and Garage Equipment Supply.