Normal driving usually won’t knock the wheels out of alignment or damage the suspension. However, normal driving also involves encounters with the unexpected, which often includes potholes, curbs, railroad crossings (which are famous for being rough), parking lot speed bumps and other things that jar and stress the suspension. For this reason, periodic alignment checks are a good way to ensure proper wheel alignment and to detect damaged, worn or bent parts that might need attention.

 

Take a bent steering arm, for example. A bent arm will change toe alignment. Toe misalignment can scrub the rubber off a set of tires as fast as any lead-footed teenager with an attitude. Only 1/8 inch of toe misalignment produces scrub equivalent to dragging the tire sideways 28 feet for every mile that’s traveled! So if you see a feathered wear pattern on the tires or what looks like camber wear on the inside or outside shoulders of both front tires (radials primarily), toe is probably out of alignment. Shoulder wear on both outside edges can be caused by toe-in while shoulder wear on both inside edges can result from toe-out.

 

Measuring the distance between each control arm and wheel is another way to find a bent steering arm. Both distances should be the same on both sides of the vehicle. If one arm is closer or further from the wheel than the other, it will not allow equal toe changes on both sides when the wheels are steered.

 

Pulling down the suspension and checking for uneven toe changes side-to-side is yet another “trick” that can be used to find this kind of “hidden” damage. If a steering arm is bent, one side will show a greater toe change than the other.

 

If you find evidence of a bent arm (unequal toe-out change or a difference in the distance from the steering arm to the wheel side-to-side), it may not be obvious which arm is the one that is bent. Obviously, there is a difference, but which arm is the one that is bent? You may have to compare steering arm to wheel measurements on another vehicle of the same year, make and model to determine which arm is bent. 

CAMBER CLUES

Camber can affect directional stability. A vehicle will lead towards the side with the most camber. So always compare camber readings on both sides. More than half a degree difference can cause a steering pull.

If camber is off on one side only, a close encounter with a pothole or curb may have bent a spindle, control arm or strut. A shift in the position of a strut tower can cause the same thing. A shift in the position of a crossmember, on the other hand, will usually change camber on both sides.  

 

One way to identify hidden damage that may be affecting camber is to do a “jounce/rebound camber check.” Raise the suspension four inches and read camber on both sides. Then compress the suspension four inches and read the camber angles for both wheels again.

 

Different camber readings side-to-side with a jounce/rebound camber check usually indicates a bent strut that needs to be replaced or straightened. If the readings are the same, a check of the “steering axis inclination” (SAI) angle side-to-side should also be made.  

SAI, THE DIAGNOSTIC ANGLE

You can zero in on the hidden damage (a bent or mislocated strut, bent control arm and/or bent spindle) by comparing the SAI angle, camber reading and “included angle” (the angle between camber and SAI). 

 

Here’s another way to check for strut problems. Loosen the two camber adjustment cam bolts on the strut (if provided), push the steering knuckles in as far as they’ll go towards negative camber and measure the distance between the strut and brake rotor on both sides. Then compare readings. If both distances are the same, you can rule out misalignment at the bottom end of the strut or a bent spindle. If they’re different, one of the struts is bent.

 

Bending a strut to “realign” the front end is no answer because you shouldn’t fix one problem by creating another. Bending a strut may bring camber back into range — assuming the wheel isn’t off more than one and a half degrees (which is the maximum limit for bending any strut). But bending a perfectly good strut to compensate for misalignment elsewhere is going to create unequal camber changes side-to-side during jounce and rebound which may create a bump steer condition. There is also a risk of weakening the strut, which may lead to strut failure later.

 

To check for a bent strut shaft, loosen the large shaft nut at the top of each strut and rotate the shaft 360 degrees while keeping an eye on the camber reading. If the shaft is bent, the top of the wheel will wobble in and out, and the camber reading will change as the shaft turns. No change in the camber reading means there’s nothing wrong with the strut. A strut with a bent shaft must be replaced. There’s no way to safely straighten this kind of damage because attempting to bend a hardened shaft will likely crack it.