Tech Tip: Ford/Mercury Experiences Loss Of Second And Fourth Gear

Tech Tip: Ford/Mercury Experiences Loss Of Second And Fourth Gear

Some 2007-'08 Escape and Mariner vehicles equipped with a CD4E transmission may experience a loss of second and fourth gear. Begin the service procedure by checking the transmission fluid condition. Refer to Workshop Manual (WSM), Section 307-01A. Does the fluid condition pass evaluation?

Vehicles affected: 2007-’08 Ford Escape and Mercury Mariner

Some 2007-’08 Escape and Mariner vehicles equipped with a CD4E transmission may experience a loss of second and fourth gear.

Service Procedure
1. Check the transmission fluid condition. Refer to Workshop Manual (WSM), Section 307-01A.
Does the fluid condition pass evaluation?

a. No – this article does not apply, refer to WSM, Section 307-01A for normal diagnostics.

b. Yes – proceed to Step 2.

2. Remove the automatic transaxle.

3. Remove the torque converter and pump shaft from the transmission.

4. Remove the turbine speed sensor (TSS) from the pump; discard the TSS O-ring seal.

5. Position the transaxle so the pump assembly is facing upward.

6. Remove the servo cover retaining ring, servo cover, servo piston and return spring.

7. Remove the pump assembly while holding the rotating parts in place using a screwdriver inserted through the turbine speed sensor hole in the pump while removing the pump assembly. See Figure 1.

figure 1

8. Remove the intermediate and overdrive band assembly from the case. Be sure to get all pieces and make sure no contamination is left inside the transmission. See Figure 2.
– Choose the correct band for application from ­­
the kit:
 – four-cylinder engines require light-colored ­friction material; and
– six-cylinder engines require dark-colored friction material.

Figure 2

9. Install the intermediate and overdrive band assembly into the case.

10. Install the #1 pump support thrust bearing onto the pump support with petroleum jelly.

11. Install the pump assembly into the case with a new pump separator plate gasket and outer pump body O-ring.

12. Measure servo travel; select and install the correct length servo rod assembly.

13. Install a new servo cover and retaining ring.

14. Install a drain plug using thread sealer on the threads, torque to 25 Nm (18 lb.-ft.).

15. Install a new O-ring on the TSS sensor and install the sensor into the pump.

16. Position the transmission top side up.

17. Install the pump driveshaft and torque ­converter.

18. Install the automatic transaxle.

Courtesy of Mitchell 1

You May Also Like

BendPak Founder Don Henthorn Passes Away

Grew company from small machine shop to global leader in car lifts and garage equipment.

Don Henthorn, owner and founder of BendPak Inc., peacefully passed away at home Thursday, March 28, at the age of 85. Under his leadership, BendPak has grown from a small machine shop to one of the world’s leading manufacturers of car lifts and automotive service equipment.

Management and operations of the privately owned company are unchanged. 

New Snap-on Limited Edition Speed Demon Roll Cab

Features include next-level organization, durability, security, mobility and exclusive Speed Demon emblem.

AMD-035 Membrane Dryer Provides Ultra-Clean & Ultra Dry Air

The dryer has a flow rating of 35 SCFM and maximum working pressures of 150 PSI.

BendPak Full-Rise Scissor Lift Delivers Two-Post Performance

SP-7XE scissor lift lays flat and raises a vehicle six feet with an open center below.

BendPak to Debut Eight-Armed Car Lift Concept at NADA

Octa-Flex improves technician productivity, convenience and ergonomics, according to BendPak.

Other Posts

TOPDON USA Makes $25,000 Donation to TechForce Foundation

To date, TOPDON has donated over $66,000 to aid organizations and schools that are dedicated to preparing the next generation of auto technicians around the world.  

Registration Open for ETI ToolTech 2024

The event will be held on April 22-24, 2024 in Newport Beach, CA, at the VEA Newport Beach Marriott.

TEXA Releases IDC5 CAR 76.5.0 Update

IDC5 CAR 76.5.0 is characterized by over 2600 new possible selections for the major makes on the market worldwide.

ISN Expands Freedom Program for Mobile Tool Dealers

ISN’s Freedom Program is designed to provide experienced, successful mobile tool dealers with support to become an independent mobile dealer and expand their growth.