Returning Brake Rotors To 'Like New' Condition

Returning Brake Rotors To ‘Like New’ Condition

When it comes to returning brake rotors to "like new" condition, it is a two-step process that can be different every time. If the vehicle has a pulsation symptom or complaint, it pays to perform a diagnostic check before machining the rotor in terms of both time and additional parts sales.

When it comes to returning brake rotors to “like new” condition, it is a two-step process that can be different every time. If the vehicle has a pulsation symptom or complaint, it pays to perform a ­diagnostic check before machining the rotor in terms of both time and additional parts sales.

 

initial check, step 1

Initial Check 

1. Hold the rotor in place with the lug nuts. Conical washers may be required on some vehicles.

2. Measure the rotor’s thickness and determine if it can be machined. If no out-of-the-ordinary problems are present, you can now proceed to machining the rotor.

 

 

 

 

 

 

 

 

 

Symptom-Based Diagnosis

1. If the vehicle has a pulsation problem or other unusual symptoms, it may be necessary to perform a pre-machining diagnosis with a dial indicator to determine if machining the rotor will resolve the problem. This stage can save time by isolating the problem.

2. At this point on the rotor, it has .005” of runout. Mark this point on the hub of the rotor and the closest lug bolt (indexing). Reinstall the rotor with the high spot 180º from the previous position of the hub and measure the runout. This check can give you an idea if the runout is in the rotor or in the hub.

3. Clean the hub’s mounting face. 

4. Up to .009” of lateral runout over factory specification can be corrected using a tapered runout correction plate that fits between the rotor and flange. These can be used alone or with an on-the-car brake lathe. Using these shims in conjuction with an on-the-car brake lathe can minimize the amount of material removed and create a more thermally balanced machined rotor.

5. Measure the runout at the hub’s face with the dial indicator. The amount of runout at the hub’s flange is a constant and cannot be machined out, only replacement can resolve the problem. 

 

 

Using an On-the-Car Lathe 

1. Mount the on-the-car lathe’s adapter to the rotor. Make sure the adapter is right for the vehicle and it is torqued down properly. 

2. Every on-the-car lathe has its own lateral runout compensation method. Alway follow the recommended procedures.  

3. Set the cutting bits to the appropriate cutting depth.

4. Once the cutting depth is set, bring the cutting head to the inside edge of the rotor’s surface.

5. Start the final cut. On some lathes, you can adjust the speed of the spindle and crossfeed.

6. Make sure you catch all the metal particles.

7. Measure the thickness of the rotor at three points. 

• If you performed a “symptom-based diagnosis,” you might want to confirm that there is no runout. Always measure at three points.

 

 

 

 

Final Assembly

1. Clean the rotor to remove all metal ­particles from the surface. Install the new pads and attach the caliper.

2. Reinstall the wheel with either a torque stick or torque wrench.

You May Also Like

Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Scan Tool

If there’s a truth that extends across all computerized devices, it’s that we likely utilize only a fraction of the things they have the ability to do. Mobile phones are a great example. How many people do you know who only use them for calls, voicemail and text messages? We all know they do so much more.The scan tools we use every day fall into the same category. Are you maximizing yours to their full potential? Don’t let them be just an expensive code reader. That may be easier said than done, because it takes a lot of time to understand both the scan tool and how well it interacts with the vehicles you’re working on, but there are a few factors that can help you dive a little deeper into the functions at your fingertips.

Brake Lathe Basics

Resurfacing drums and rotors is a machining process with its own specific guidelines.

Refrigerant Oil Has to Be Right

Oil type is just as important as oil capacity.

Three bottles of refrigerant oil
Top 5 Tools: Steve Coffell, Auto World, Hazelwood, MO

Steve Coffell, a technician at Auto World in Hazelwood, MO, says his Top 5 Favorite Tools are: Related Articles – Lisle Low Profile Fuel Line Disconnect – Dent Fix Soft-Shock Mallet DF-SM76 Reduces Damage – New ProMAXX Diesel Fuel Injector Seal Puller/Saver ProKits   OTC Genisys Touch – Quick scan, bidirectional control Snap-on VANTAGE Pro

Wheel Bearing Adjustment Tools & Equipment

A wheel bearing that’s out of adjustment can reduce bearing life and can affect more than just the bearing. It’s important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. There are a few types of assemblies, so using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Other Posts

2024 Is Your Year to Be the Technician You Always Wanted to Be

As we enter 2024, strategic career planning is essential for success in the automotive repair industry.

happy new year 2024
Impact Wrench Technology

Interchangeable anvils are a feature on some new impacts.

Tools in the Eye of the Beholder

We’re here to help you see all the tools, so you can invest wisely.

Multimeter Accuracy: How Important Is It?

Multimeter accuracy is critical for EV diagnostics.

multimeter