Beyond the Warranty Maintenance Checklist

Beyond the Warranty Maintenance Checklist

What happens after the bumper-to-bumper and powertrain warranties wear out? If you look at any factory-recommended service intervals, after 100,000 miles they cease to exist. What does it take to keep a vehicle going for 120,000, 180,000 or 250,000 miles? The key is maintenance and

What happens after the bumper-to-bumper and powertrain warranties wear out? If you look at any factory-recommended service intervals, after 100,000 miles they cease to exist.
What does it take to keep a vehicle going for 120,000, 180,000 or 250,000 miles? The key is maintenance and ­inspection. 

125,000 miles is almost five times around the planet. With all of the warranties expired, it is up to the owner and their repair shop to keep it rolling. Here are 13 items you should service. 
Coolant: Many OEMs have a replacement interval of 125,000 miles. While the coolant does not lose its ability to transfer heat, the additive package loses its ability control corrosion and the pH level of the coolant. 
Spark Plugs: Every time a spark plug fires, the plasma of the spark wears away the electrodes. This causes the gap to increase. As the gap increases, it requires more energy to fire the plug. This can take its toll on the coils. 
Oxygen Sensors: By the time a vehicle has reached 120,000 miles, it might have burned more than 5,000 gallons of fuel (about the volume of the average above-ground pool). Combustion byproducts can accumulate on the sensor and cause it to respond slower to fuel ­mixture changes. 
Transmission Fluid: The typical OE service interval can range from 60,000 miles to “lifetime.” Many modern transmissions do not even have a filter. Changing the fluid in the transmission on a regular basis will keep internal wear in check.
Belt Tensioner: If a vehicle has made it this far, the belt tensioner might need to be replaced, along with the belt. As the spring inside the tensioner fatigues, it can cause the belt to jump and vibrate. Also check the idler pulleys for noise and bearing leaks.
Decoupler ­Pulleys: Some late-model ­alternator pulleys wear out in as little as 60,000 miles. These overrunning ­alternator decoupler (OAD) ­pulleys or one-way clutches ­increase engine efficiency and decrease vibration. Their failure can cause other accessory drive components to wear out prematurely, a no-charge condition, a weak battery, and/or a decrease in fuel economy. 
Alignment: Vehicles should be aligned more often as they get older to monitor suspension bushings and springs. Ride height should be measured at every alignment.  
A/C: One expendable part of the system is the A/C compressor clutch. Like a clutch between the engine and transmission, it can wear out and slip. Most vehicles have an inspection procedure and specification for the clutch.
Some AWD and 4WD vehicles have three differentials that need service. Ignoring these can lead to an expensive repair. Some manufacturers may not specify a service interval, but that does not mean they don’t need to be serviced.
Filters: The fuel filter should be replaced to prolong the life of the fuel pump and potentially the engine. Modern fuel pumps are sensitive to restrictions and the pump will have to work harder if a restriction is present.  
Shocks & Struts: The recommended replacement ­interval for shocks and struts is 50,000 miles. According to one ride control manufacturer, a typical shock and strut “strokes” an average of 1,750 cycles per mile – that’s 21 million cycles per 12,000 miles!
Brake Fluid: Brake fluid should be replaced when the boiling point drops or the concentration of the copper brazing in the fluid indicates corrosion in the system. Replacing the brake fluid restores pH buffers and anti-corrosion chemicals that can extend the life of the calipers, master cylinder and ABS modulator.
Combustion Chamber: Carbon can build up on the crown of the piston, valves and head. If the carbon ­deposits get too heavy, they can cause turbulence in the chamber, hot spots and even an increase in the compression ratio. Newer vehicles are more sensitive to this ­because of the advanced ­design of their combustion chambers and higher compression ratios. Engine ­de-carbonization can help ­remove these ­deposits. 
When a vehicle reaches 180,000 miles, wear between the cylinder walls and piston rings could start to show. Gases from the crankcase into the combustion chamber can cause carbon deposits and damage the catalytic converter and O2 sensors. Blowby from the combustion chamber to the crankcase can also cause contaminated oil and bearing damage. 
This type of wear kills an engine. If the customer kept up with regular oil changes and the previously listed items, the investment is ­starting to pay off at 180,000 miles. At this milestone, there are other maintenance items a shop should pay ­attention to in addition to the 125,000-mile recommendations.  
Timing Chain Tensioners: Timing chain guides are ­designed to wear. They are made of composite materials that can become brittle when exposed to heat cycles and engine oil over time. Oil-pressurized tensioners can wear and leak. The most common sign of failure is noise, timing skips and/or a check engine light. Inspect and replace these items ­before they kill the engine.
MAF Sensor: By 180,000 miles, the engine will have consumed more than an Olympic-sized pool of air. Even with a filter, the mass airflow sensor will become contaminated. Cleaning the sensor can restore performance and fuel economy.  
Engine and Transmission Mounts: Worn motor and transmission mounts can turn an engine into a wrecking ball. If a worn mount is ­ignored, it can cause exhaust system leaks and shifter cable failures.
Power Steering Fluid: Anti-corrosion and anti-foaming additives in power steering fluid will break down over time, accelerating wear on the pump and rack. The fluid will not appear to be contaminated, but it does need to be changed. 
Drivetrain Seals: Seals on axles and ­driveshafts need to be inspected regularly. While a leaking seal may not cause a breakdown, the loss of fluid will. Recommend replacement at the first sign of a leak. Seals are cheap insurance on very ­expensive components.
A/C: The performance of an HVAC system can be ­determined with an anemometer that measures wind speed. This tool can be used to spot restrictive cabin air filters, stuck doors or weak ­blower motors. 
Headlights: Inspect and adjust the headlights. The ­adjusters inside the lights can be damaged over time by ­vibration and heat. UV rays and road debris can damage the headlight lens, leaving it yellow and foggy. There are professional ­solutions to headlight refinishing that are profitable and efficient.
The moon is approximately 238,000 miles away. If a ­vehicle has made it this far, chances are that it’s not by ­accident. 
Chassis Inspection: Alignment plays an important role in measuring the health of the chassis. Toe that is outside of the specification can indicate a worn or ­broken spring. ­Excessive camber can ­reveal a soft control arm bushing.  
Fuel Injector Cleaning: At 250,000 miles, more than 10,000 gallons of fuel have been pumped through very small holes in the injectors. An injector’s needle and seat also have been crashing into each other millions of times. Carbon can build up on the caps and the fuel spray pattern might not be what it once was. You can perform a fuel injector cleaning on the car, or you can send the injectors out for ­ultrasonic cleaning. 
A/C: Pay attention to the condenser, air dam and shrouds. On some vehicles, a significant amount of debris may have built up between the condenser and radiator. 
Catalytic Converter: Check for any physical damage and hit it with a hammer to make sure that the ceramic biscuits are tightly held in place. If the driver has kept up with general maintenance, like oil changes and fuel injector service, the ­converter might be operational within the specifications.  

You May Also Like

Prevent Cold Stress with 3 Steps for Choosing Winter PPE

Protect workers from hypothermia, frostbite, and other dangerous illnesses.

Safety is a full-time job that doesn’t get any easier in the winter months when extreme temperatures, high winds, and wet conditions give safety managers and workers more to worry about. Workers who are exposed to cold environments are at risk for cold stress which can lead to dangerous conditions such as hypothermia, frostbite, trench foot, and chilblains. According to the US Bureau of Labor Statistics’ most recent Injuries, Illness, and Fatalities Report, nearly 14,000 workplace injuries could be attributed to ice, sleet, or snow. 

ProovStation, MICHELIN Unveil TireStation

The TireStationsolution was presented at CES 2023 in Las Vegas.

ProovStation and MICHELIN have unveiled TireStation, the fast and reliable solution for automated tire inspection.
Hunter Adds FastBlast Feature to 51H Tire Changer 

The FastBlast system is designed to inflate even the most challenging truck and SUV tires.

FlastBlast™, Hunter Engineering’s topside blast inflation system, is now an option for its popular TCX51H tire changer. This new configuration will be known as 51H Plus.
Rotary Alignment Lift Offers Wide Service Capacity Range

Shops can offer alignment services with bay space to spare, and techs can perform alignments on a wider range of vehicles.

Rotary, part of Vehicle Service Group (VSG), a Dover company, announces the addition of the new XA12 Alignment Scissor Lift to its extensive line of automotive lifts for independent shop owners, dealership service departments and car enthusiasts.
See More Details with New Lens Technology from Miller

ClearLight 2.0 allows more natural, accurate color tones to come through the lens.

New ClearLight 2.0 Lens Technology uses advanced, high-definition optics for the most realistic view that’s clearer and brighter — before, during and after every weld.

Other Posts

New Digital Lifting Points Guide from ALI

Electronic guide makes it easy to find OEM lifting point information.

Auto Techcelerators Joins Opus IVS

Combination opens new opportunities for innovation and productivity advances in ADAS services processes.

Opus IVS Introduces QuickADAS 

ADAS calibration workflow that launches directly into self-serve calibration from the on-screen ADAS checklist on IVSMap.

SUN Offers Subscription with John Bean ADAS Tool

Shops that purchase a Tru-Point ADAS system will receive a two-month subscription to SUN Collision Repair Information.